VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1361, C146C, C146D

DTC Code DTC Name
C1361 Short in ABS Motor Fail Safe Relay Circuit
C146C Open in ABS Motor Relay Circuit
C146D Short in ABS Motor Relay Circuit

DESCRIPTION

These DTCs are stored when a problem is identified in the skid control ECU (brake actuator assembly).

The ABS motor relay supplies power to the pump motor. While the ABS is activated, the ECU turns the ABS motor relay on and operates the pump motor.

If the voltage supplied to the ABS motor relay (BM) is below the DTC detection threshold due to low voltage from the battery or alternator, these DTCs may be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1361 Short in ABS Motor Fail Safe Relay Circuit Immediately after the engine switch is turned on (IG), the relay contact is closed for 4 seconds when the ABS motor fail-safe relay is off.

  • ABS motor fail-safe relay circuit

  • Skid control ECU (brake actuator assembly)
C146C Open in ABS Motor Relay Circuit

Either of the following is detected:


  • All of the following conditions are met for 0.12 seconds or more.


    • The IG1 terminal voltage is 9.5 V or more.

    • Initial check is being performed, or ABS, BA, TRC or VSC is operating.

    • Relay contact remains open when the relay is turned on.

  • Both of the following conditions are met for 0.12 seconds or more.


    • The IG1 terminal voltage is less than 9.5 V.

    • Relay contact remains open when the relay is turned on.

  • ABS NO. 2 fuse

  • ABS motor relay circuit

  • Skid control ECU (brake actuator assembly)
C146D Short in ABS Motor Relay Circuit When the ABS motor relay is turned off, the ABS motor relay remains closed for 4 seconds or more. Skid control ECU (brake actuator assembly)
C146C DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status The IG1 terminal voltage is 9.5 V or more. ○ -
Initial check is being performed, or ABS, BA, TRC or VSC is operating. ○ -
Relay contact remains open when the relay is turned on. ○ -
The IG1 terminal voltage is less than 9.5 V. - ○
Relay contact remains open when the relay is turned on. - ○
Detection Time 0.12 seconds or more. 0.12 seconds or more.
Number of Trips 1 trip 1 trip

Tech Tips

DTC will be output when conditions for either of the patterns in the table above are met.

Tech Tips

for C146C: Even after the trouble areas are repaired, the ABS warning light will not go off unless the following operations are performed:


  1. Drive the vehicle at 30 km/h (19 mph) for 30 seconds or more and check that the ABS warning light goes off.

  2. Clear the DTCs.

WIRING DIAGRAM

A01XQ1DE01

CAUTION / NOTICE / HINT

Note


  • When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Tech Tips

When C1241 and/or C1417 is output together with C1361, C146C and/or C146D, inspect and repair the trouble areas indicated by C1241 and/or C1417 first.

for C1241: Click here

for C1417: Click here

PROCEDURE


  1. INSPECT HARNESS AND CONNECTOR (BM TERMINAL)


    1. A01XRI0C01
      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Actuator Assembly))

      Make sure that there is no looseness at the locking part and the connecting part of the connector.

    2. Disconnect the A9 skid control ECU (brake actuator assembly) connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A9-24 (BM) - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BM CIRCUIT)

    OK

  2. CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)


    1. A01XQZ4C01
      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Actuator Assembly))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A9-13 (GND2) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)

    OK

  3. RECONFIRM DTC

    Tech Tips

    The ABS motor relay is in the skid control ECU (brake actuator assembly). Therefore, ABS motor relay inspection and ABS motor relay unit inspection cannot be performed. Be sure to check if any DTCs are output again before replacing the skid control ECU (brake actuator assembly).


    1. Reconnect the A9 skid control ECU (brake actuator assembly) connector.

    2. Turn the engine switch off.

    3. Clear the DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Clear DTCs

    4. Turn the engine switch off.

    5. Start the engine.

    6. Perform a road test.

    7. Check if the same DTC is output.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Result
      Result Proceed to
      DTCs C1361, C146C and C146D are not output. A
      DTCs C1361, C146C and/or C146D are output. (for LHD) B
      DTCs C1361, C146C and/or C146D are output. (for RHD) C

      Tech Tips


      • If a speed signal of 6 km/h (4 mph) or more is sent to the skid control ECU (brake actuator assembly) with the engine switch on (IG) and the stop light switch assembly off, the ECU performs self diagnosis of the motor and solenoid circuits.

      • If the normal system code is output (no DTCs are output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly).

      • If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

      • If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.


    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

    C

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here