VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1429

DTC Code DTC Name
C1429 Open or Short in Brake Pedal Load Sensing Switch

DESCRIPTION

The brake pedal load sensing switch (brake pedal support assembly) turns on when the brake pedal is depressed with a force exceeding a predetermined level.

The skid control ECU (brake actuator assembly) uses this circuit to detect if the brake pedal is depressed or not.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C1429 Open or Short in Brake Pedal Load Sensing Switch When the voltage at terminal +BS is 9.5 V or higher, an open or short in the brake pedal load sensing switch continues for 0.3 seconds or more.

  • Brake pedal load sensing switch (brake pedal support assembly)

  • Brake pedal load sensing switch circuit

  • Skid control ECU (brake actuator assembly)

 -

WIRING DIAGRAM

B002DOKE28
*a Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly)
*b Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

Note

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click here

PROCEDURE


  1. READ VALUE USING GTS (BRAKE PEDAL LOAD SENSING SW)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Select the Data List using the GTS.

      Click here


      Chassis > ABS/VSC/TRC > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Brake Pedal Load Sensing SW Brake pedal load sensing switch ON or OFF

      ON: Brake pedal depressed beyond a specified point

      OFF: Brake pedal not depressed beyond a specified point

      		 -

      Chassis > ABS/VSC/TRC > Data List
      Tester Display
      Brake Pedal Load Sensing SW

    4. Check that the brake pedal load sensing switch display observed on the GTS changes according to brake pedal operation.

      OK
      The GTS displays ON or OFF according to brake pedal operation.
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT BRAKE PEDAL SUPPORT ASSEMBLY Click here

    OK

  2. RECONFIRM DTC


    1. Clear the DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Clear DTCs

    2. Turn the engine switch off.

    3. Start the engine.

    4. Perform a road test.

    5. Check if the same DTC is output.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Result
      Result Proceed to
      DTC C1429 is not output. A
      DTC C1429 is output. (for LHD) B
      DTC C1429 is output. (for RHD) C

    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

    C

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

  3. INSPECT BRAKE PEDAL SUPPORT ASSEMBLY


    1. Inspect the brake pedal load sensing switch (brake pedal support assembly).

      Click here

      OK
      The brake pedal load sensing switch (brake pedal support assembly) is normal.
      Result
      Result Proceed to
      OK A
      NG (for LHD) B
      NG (for RHD) C

    B

    REPLACE BRAKE PEDAL SUPPORT ASSEMBLY Click here

    C

    REPLACE BRAKE PEDAL SUPPORT ASSEMBLY Click here

    A

  4. CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL SUPPORT ASSEMBLY)


    1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

    2. Disconnect the A52 skid control ECU (brake actuator assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A52-23 (FSW+) - A4-2 (FSW+) Always Below 1 Ω
      A52-23 (FSW+) or A4-2 (FSW+) - Body ground Always 10 kΩ or higher
      A4-1 (FSW-) - Body ground Always Below 1 Ω
      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG C

    A

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

    B

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR