REAR SHOCK ABSORBER INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL REAR NO. 1 SPRING BUMPER


    1. Install the rear No. 1 spring bumper to the rear shock absorber assembly.

  2. INSTALL REAR SUSPENSION SUPPORT ASSEMBLY


    1. A01XR4KC01
      *1 Rear No. 2 Shock Absorber Cushion
      *2 Rear Suspension Support Assembly
      *3 Rear No. 1 Shock Absorber Cushion
      *4 Rear Shock Absorber Cushion Washer
      *5 Rear Actuator Support Bracket

      Install the rear actuator support bracket, rear No. 2 shock absorber cushion, rear suspension support assembly, rear No. 1 shock absorber cushion and rear shock absorber cushion washer to the rear shock absorber assembly.

      Note

      Be sure to install the rear shock absorber cushion washer in the correct direction.

    2. Temporarily tighten a new rear support to rear shock absorber nut.

    3. A01XRLMC03
      *1 Rear Shock Absorber Lower Bushing
      *2 Rear Suspension Support Assembly
      *a Rear Shock Absorber Lower Bushing Axis Line
      *b Rear Suspension Support Assembly Stud (Toward Vehicle Interior) 2-point Axis Line
      B002DP3 Front of the Vehicle

      Align the rear suspension support assembly so that the stud bolts of the rear suspension support assembly are positioned as shown in the illustration.

    4. Secure the rear actuator support bracket of the rear shock absorber assembly between aluminum plates in a vise.

      Note

      Do not overtighten the vise.

    5. Using a 17 mm deep socket wrench, fully tighten the rear support to rear shock absorber nut.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

      Note


      • Do not pinch the wire harness when tightening the rear support to rear shock absorber nut with the deep socket wrench.

      • When inserting the wire harness and connector into the deep socket wrench, do not excessively bend the wire harness.

  3. INSTALL REAR SHOCK ABSORBER ASSEMBLY (for Upper Side)


    1. Install the 3 nuts to the upper side of the rear shock absorber assembly.

      Torque:
      74 N*m  { 755 kgf*cm, 55 ft.*lbf }

    2. Engage the 2 clamps and install the actuator harness clamp to the vehicle body.

    3. Engage the wire harnesses clamp to the actuator harness clamp.

    4. Connect the connector.

  4. INSTALL REAR LOWER COIL SPRING INSULATOR

    Click here

  5. INSTALL REAR UPPER COIL SPRING INSULATOR

    Click here

  6. INSTALL REAR COIL SPRING

    Click here

  7. TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY (for Lower Side)

    Click here

  8. INSTALL REAR STABILIZER LINK ASSEMBLY

    Click here

  9. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY

    Click here

  10. CONNECT REAR STEERING TIE ROD ASSEMBLY

    Click here

  11. STABILIZE SUSPENSION


    1. A01XRBFC01
      *a Wooden Block
      *b Jack
      B002CL1 Wooden block placement location

      Using a jack and wooden block, apply load to the suspension so that the rear No. 2 suspension arm assembly is positioned as shown in the illustration.

      CAUTION:


      • Do not raise the jack up too high.

      • The vehicle could fall, resulting in a serious accident.

      B002EYR

      Note


      • When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

      • Make sure to perform this operation with the vehicle kept as low as possible.

      Standard Length (A)
      18.1 mm (0.713 in.)

  12. INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

    Click here

  13. INSTALL REAR SHOCK ABSORBER ASSEMBLY (for Lower Side)


    1. B002CJK

      Install the rear shock absorber assembly with the bolt.

      Torque:
      110 N*m  { 1122 kgf*cm, 81 ft.*lbf }

      Note

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

  14. INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY

    Click here

  15. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY

    Click here

  16. INSTALL REAR SUSPENSION ARM COVER

    Click here

  17. INSTALL REAR WHEEL

    Click here

  18. INSTALL LUGGAGE COMPARTMENT TRIM COVER

    Click here

  19. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

    Click here

  20. INITIALIZE HEIGHT CONTROL SENSOR SIGNAL

    Click here

  21. ADJUST HEADLIGHT AIMING

    Click here