TORQUE VECTORING DIFFERENTIAL SYSTEM, Diagnostic DTC:C2A26, C2A27

DTC Code DTC Name
C2A26 RH Oil Temperature Sensor Fixation Malfunction
C2A27 LH Oil Temperature Sensor Fixation Malfunction

DESCRIPTION

The torque vectoring differential ECU assembly compares the engine coolant temperature and torque transfer module temperature when the engine switch is off. If the torque vectoring differential ECU judges that the sensor output value is stuck, a DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate
C2A26 RH Oil Temperature Sensor Fixation Malfunction

Diagnosis Condition:


  • IG power source voltage is 10 V or more.

Abnormal condition:


  • Temperature sensor output value of the torque transfer module (RH side) is stuck.

Malfunction Time:


  • 3 seconds or more

Trip logic:


  • 1 trip detection logic

  • Torque vectoring differential ECU assembly

  • Temperature sensor (RH side)

  • Master Warning Light: Comes on

  • Multi-information Display Error Message: Comes on
C2A27 LH Oil Temperature Sensor Fixation Malfunction

Diagnosis Condition:


  • IG power source voltage is 10 V or more.

Abnormal condition:


  • Temperature sensor output value of the torque transfer module (LH side) is stuck.

Malfunction Time:


  • 3 seconds or more

Trip logic:


  • 1 trip detection logic

  • Torque vectoring differential ECU assembly

  • Temperature sensor (LH side)

  • Master Warning Light: Comes on

  • Multi-information Display Error Message: Comes on

WIRING DIAGRAM

Refer to the wiring diagram for DTC C2A12.

Click here

CAUTION / NOTICE / HINT

Tech Tips

If the torque vectoring differential ECU assembly has been replaced, perform "All Learning".

Click here

PROCEDURE


  1. CHECK DTC OUTPUT (TVD)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Enter the following menus: Chassis / TVD / Trouble Codes.

    4. Check for DTCs.


      Chassis > TVD > Trouble Codes
      Result
      Result Proceed to
      DTC C2A26 is output. A
      DTC C2A27 is output. B
      DTCs other than DTC C2A26 and DTC C2A27 are output. C
      DTCs are not output. D

    5. Turn the engine switch off.


    B

    READ VALUE USING GTS (LH OIL TEMPERATURE) Click here

    C

    GO TO DTC CHART Click here

    D

    CHECK FOR INTERMITTENT PROBLEMS Click here

    A

  2. READ VALUE USING GTS (RH OIL TEMPERATURE)


    1. Disconnect the torque transfer module motor sub-assembly (RH side) connector.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG).

    4. Enter the following menus: Chassis / TVD / Data List / RH Oil Temperature.


      Chassis > TVD > Data List
      Tester Display
      RH Oil Temperature
    5. B002CZNC06
      *1 Torque Transfer Module Motor Sub-assembly (RH Side)
      *a Temperature Sensor (RH Side) Connector

      Read the Data List when there is an open or short in the temperature sensor (RH side) circuit.

      Standard Resistance
      Tester Display Condition Specified Condition
      RH Oil Temperature Open between TMPR and TMGR Below -40°C (-40°F)
      Short between TMPR and TMGR 200°C (392°F) or higher

    6. Turn the engine switch off.

    7. Reconnect the torque transfer module motor sub-assembly (RH side) connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE TEMPERATURE SENSOR (RH SIDE) Click here

    NG

    REPLACE TORQUE VECTORING DIFFERENTIAL ECU ASSEMBLY Click here

  3. READ VALUE USING GTS (LH OIL TEMPERATURE)


    1. Disconnect the torque transfer module motor sub-assembly (LH side) connector.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG).

    4. Enter the following menus: Chassis / TVD / Data List / LH Oil Temperature.


      Chassis > TVD > Data List
      Tester Display
      LH Oil Temperature
    5. B002CZNC07
      *1 Torque Transfer Module Motor Sub-assembly (LH Side)
      *a Temperature Sensor (LH Side) Connector

      Read the Data List when there is an open or short in the temperature sensor (LH side) circuit.

      Standard Resistance
      Tester Display Condition Specified Condition
      LH Oil Temperature Open between TMPL and TMGL Below -40°C (-40°F)
      Short between TMPL and TMGL 200°C (392°F) or higher

    6. Turn the engine switch off.

    7. Reconnect the torque transfer module motor sub-assembly (LH side) connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE TEMPERATURE SENSOR (LH SIDE) Click here

    NG

    REPLACE TORQUE VECTORING DIFFERENTIAL ECU ASSEMBLY Click here