IGNITION COIL AND SPARK PLUG INSTALLATION

PROCEDURE


  1. INSTALL SPARK PLUG

    Click here

  2. INSTALL IGNITION COIL ASSEMBLY

    Tech Tips

    Perform "Inspection After Repair" after replacing an ignition coil assembly.



    1. Install the 8 ignition coil assemblies to the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH with the 8 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      If an ignition coil assembly has been struck or dropped, replace it.

      Tech Tips

      Install the same parts to their original positions.

    2. Connect the 8 ignition coil assembly connectors.

  3. INSTALL SUCTION PIPE SUB-ASSEMBLY


    1. Install the suction pipe sub-assembly to the suction tube bracket with the bolt.

      Torque:
      9.8 N*m  { 100 kgf*cm, 87 in.*lbf }

  4. INSTALL NO. 3 ENGINE ROOM RELAY BLOCK (for LHD)


    1. B002EIDC01
      *A Bolt Type A
      *B Bolt Type B
      *C Bolt Type C
      *D Bolt Type D

      Install the wire harness clamp bracket with the bolt.

      Tech Tips

      The tightening torque differs depending on the type of bolt.

      Torque:
      Bolt Type A
      10.5 N*m  { 107 kgf*cm, 8 ft.*lbf }
      Bolt Type B
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }
      Bolt Type C
      9.5 N*m  { 97 kgf*cm, 84 in.*lbf }
      Bolt Type D
      9.5 N*m  { 97 kgf*cm, 84 in.*lbf }

    2. Install the No. 3 engine room relay block assembly with the bolt and nut.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  5. INSTALL NO. 3 ENGINE ROOM RELAY BLOCK (for RHD)


    1. Install the wire harness clamp bracket with the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. Install the No. 3 engine room relay block assembly with the bolt and nut.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  6. INSTALL NO. 1 ENGINE ROOM RELAY BLOCK (for LHD)


    1. Install the wire harness clamp bracket with the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. Engage the wire harness clamp.

    3. Install the No. 1 engine room relay block with the 2 bolts and nut.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  7. INSTALL NO. 1 ENGINE ROOM RELAY BLOCK (for RHD)


    1. B002EIDC01
      *A Bolt Type A
      *B Bolt Type B
      *C Bolt Type C
      *D Bolt Type D

      Install the wire harness clamp bracket with the bolt.

      Tech Tips

      The tightening torque differs depending on the type of bolt.

      Torque:
      Bolt Type A
      10.5 N*m  { 107 kgf*cm, 8 ft.*lbf }
      Bolt Type B
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }
      Bolt Type C
      9.5 N*m  { 97 kgf*cm, 84 in.*lbf }
      Bolt Type D
      9.5 N*m  { 97 kgf*cm, 84 in.*lbf }

    2. Engage the wire harness clamp.

    3. Install the No. 1 engine room relay block with the 2 bolts and nut.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  8. INSTALL BATTERY TRAY


    1. Install the battery tray with the 2 bolts.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  9. INSTALL POWER STEERING ECU ASSEMBLY


  10. INSTALL V-BANK COVER SUB-ASSEMBLY

    Click here

  11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Click here

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  12. PERFORM INITIALIZATION


    1. Perform "Inspection After Repair" after replacing an ignition coil assembly and spark plug.