AIR COOLED OIL COOLER REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the oil cooler assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Removal/installation of front bumper assembly Adjust millimeter wave radar sensor assembly

  • Dynamic radar cruise control system

  • Pre-crash safety system

  • Forward recognition camera system

  • LKA/LDA system

Click here

PROCEDURE


  1. PRECAUTION

    Note

    If the bolts of the upper transmission oil cooler bracket are loosened, the oil cooler assembly may move out of position and interfere with the front bumper assembly. Do not loosen the bolts of the upper transmission oil cooler bracket.

    B002DILC02
    *1 Upper Transmission Oil Cooler Bracket
    *a Do not loosen

  2. REMOVE FRONT WHEEL RH

    Click here

  3. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

    Click here

  4. REMOVE FRONT SUSPENSION MEMBER BRACE SUB-ASSEMBLY

    Click here

  5. REMOVE NO. 2 ENGINE UNDER COVER

    Click here

  6. DRAIN AUTOMATIC TRANSMISSION FLUID

    Click here

  7. REMOVE FRONT BUMPER ASSEMBLY

    Click here

  8. REMOVE TRANSMISSION OIL COOLER AIR DUCT


    1. B002D3BC02
      *a Clamp
      *b Guide

      Disengage the clamp to disconnect the wire harness from the transmission oil cooler air duct.

    2. Remove the 2 bolts.

    3. Disengage the guide to remove the transmission oil cooler air duct from the oil cooler assembly.

  9. REMOVE OIL COOLER ASSEMBLY


    1. B002DE3C01
      *1 No. 5 Transmission Oil Cooler Hose
      *2 Cool Air Intake Duct

      Disengage the clamp to disconnect the No. 5 transmission oil cooler hose from the cool air intake duct.

    2. Slide the clip and disconnect the No. 5 transmission oil cooler hose from the oil cooler tube sub-assembly.

    3. B002CJXC01
      *1 No. 6 Transmission Oil Cooler Hose
      *2 Cool Air Intake Duct

      Disengage the clamp to disconnect the No. 6 transmission oil cooler hose from the cool air intake duct.

    4. Slide the clip and disconnect the No. 6 transmission oil cooler hose from the oil cooler tube sub-assembly.

    5. B002E0I

      Remove the 2 bolts and 3 clips to disconnect the outlet transmission oil cooler air duct from the front fender liner RH.

    6. B002EGB

      Remove the 4 nuts and oil cooler assembly with outlet transmission oil cooler air duct from the vehicle body.

    7. B002EH9

      Disengage the clamp and remove the hose clamp from the No. 6 transmission oil cooler hose.

    8. Slide the clip and remove the No. 6 transmission oil cooler hose from the oil cooler assembly.

    9. B002DBC

      Disengage the clamp and remove the hose clamp from the No. 5 transmission oil cooler hose.

    10. Slide the clip and remove the No. 5 transmission oil cooler hose from the oil cooler assembly.

    11. B002DQD

      Remove the 2 bolts and outlet transmission oil cooler air duct from the oil cooler assembly.

    12. B002EXU

      Remove the 2 nuts, 2 clips and transmission oil cooler bracket from the oil cooler assembly.

      Note

      Do not loosen the bolts of the upper transmission oil cooler bracket.

      B002DILC02
      *1 Upper Transmission Oil Cooler Bracket
      *a Do not loosen