BLACK OUT TAPE(for Front Door) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the black out tape removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control)

Click here

Simple intelligent parking assist system*1
Toyota parking assist-sensor system*1
Pre-collision system
Initialize back door lock Power door lock control system

Click here


  • Front door window regulator assembly

  • Front door glass sub-assembly

  • Front door glass run

 Initialize Power Window Control System

  • Auto up and down function

  • Jam protection function

  • Catch protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Window open warning function

Click here

*1: When performing learning using the GTS.

Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

    Click here

  4. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)

    Click here

  5. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)

    Click here

  6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

    Click here

  7. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

    Click here

  8. DISCONNECT FRONT DOOR WEATHERSTRIP

    Click here

  9. REMOVE FRONT DOOR BELT SEAL

    Click here

  10. REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP

    Click here

  11. REMOVE FRONT DOOR VENT SEAL

    Click here

  12. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY

    Click here

  13. REMOVE FRONT DOOR SERVICE HOLE COVER

    Click here

  14. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

    Click here

  15. REMOVE DOOR FRAME UPPER GARNISH

    Click here

  16. REMOVE FRONT DOOR GLASS RUN

    Click here

  17. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

    Click here

  18. REMOVE FRONT DOOR FIX WINDOW GLASS

    Click here

  19. REMOVE NO. 4 FRONT DOOR STRIPE

    Tech Tips

    When removing the No. 4 front door stripe, heat the vehicle body and No. 4 front door stripe using a heat light.

    Heating Temperature
    Item Temperature
    No. 4 Front Door Stripe and Vehicle Body 40 to 60°C (104 to 140°F)

    CAUTION:


    • Do not touch the heat light and heated parts, touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    A005MVZC23
    *a Heated Part
    *b Heat Light

    Note

    Do not heat the vehicle body excessively.


    1. Using a heat light, heat the No. 4 front door stripe and vehicle body.

    2. A005N24

      Pull back on one of the ends of the No. 4 front door stripe to remove it.

      Tech Tips

      When pulling on the No. 4 front door stripe, pull it parallel to the vehicle body.

  20. REMOVE FRONT DOOR OUTSIDE STRIPE

    Tech Tips

    When removing the front door outside stripe, heat the vehicle body and front door outside stripe using a heat light.

    Heating Temperature
    Item Temperature
    Front Door Outside Stripe and Vehicle Body 40 to 60°C (104 to 140°F)

    CAUTION:


    • Do not touch the heat light and heated parts, touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    A005MVZC23
    *a Heated Part
    *b Heat Light

    Note

    Do not heat the vehicle body excessively.


    1. Using a heat light, heat the front door outside stripe and vehicle body.

    2. A005NN3

      Pull back on one of the ends of the front door outside stripe to remove it.

      Tech Tips

      When pulling on the front door outside stripe, pull it parallel to the vehicle body.

  21. REMOVE NO. 2 FRONT DOOR STRIPE

    Tech Tips

    When removing the No. 2 front door stripe, heat the vehicle body and No. 2 front door stripe using a heat light.

    Heating Temperature
    Item Temperature
    No. 2 Front Door Stripe and Vehicle Body 40 to 60°C (104 to 140°F)

    CAUTION:


    • Do not touch the heat light and heated parts, touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    A005MVZC23
    *a Heated Part
    *b Heat Light

    Note

    Do not heat the vehicle body excessively.


    1. Using a heat light, heat the No. 2 front door stripe and vehicle body.

    2. A005NXG

      Pull back on one of the ends of the No. 2 front door stripe to remove it.

      Tech Tips

      When pulling on the No. 2 front door stripe, pull it parallel to the vehicle body.