WINDSHIELD OUTSIDE MOULDING REMOVAL

Info Added 2017-10-06

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the windshield outside moulding removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effects/Inoperative when not performed Link
Windshield glass sub-assembly Adjust forward recognition camera Dynamic radar cruise control system

Click here

Lane departure alert system (w/ Steering Control)
Pre-collision system
Forward recognition camera system
Automatic high beam system

Note

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, lane departure alert system, pre-crash safety system, forward recognition camera system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. REMOVE WINDSHIELD OUTSIDE MOULDING


    1. A005O8UC01
      B0048V2 Protective Tape

      Apply protective tape around the windshield outside moulding.

    2. A005NRWC01
      B0048R7 Remove in this Direction

      Disengage the claws and clip to disconnect the windshield outside moulding as shown in the illustration.

    3. A005NI2

      Using a moulding remover D, disengage the claws to remove the windshield outside moulding.

  2. REMOVE NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP

    Tech Tips

    Perform the following procedure only when replacement of a No. 1 windshield outside moulding clip is necessary.


    1. A005N1VC01
      B0048R7 Remove in this Direction

      Disengage the claws to remove the 5 No. 1 windshield outside moulding clips as shown in the illustration.

  3. REMOVE NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP

    Tech Tips

    Perform the following procedure only when replacement of a No. 3 windshield outside moulding clip is necessary.


    1. Remove the windshield glass sub-assembly.

      Click here

    2. Insert a 4.0 mm (0.157 in.) drill bit into a drill.

    3. A005MXKC05
      *a Tape

      Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

      Standard Measurement
      Area Measurement
      A 5.0 mm (0.197 in.)

      Note

      Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

    4. A005NFKC01
      *a Flange

      Lightly press the drill bit against the No. 3 windshield outside moulding clips to drill off the No. 3 windshield outside moulding clip flanges, and remove the 5 No. 3 windshield outside moulding clips.

      CAUTION:

      Be careful of the drilled No. 3 windshield outside moulding clips, as they may be hot.

      Note


      • Make sure to protect both the inside and outside of the vehicle as the No. 3 windshield outside moulding clip shavings will fly about.

      • Pressing the drill too firmly will cause the No. 3 windshield outside moulding clip to turn and result in the No. 3 windshield outside moulding clip not being drilled through.

      • Prying the No. 3 windshield outside moulding clip with the drill may damage the No. 3 windshield outside moulding clip installation hole or drill bit.

    5. Using a vacuum cleaner, remove the No. 3 windshield outside moulding clip fragments and shavings from the drilled areas.