WIPER AND WASHER SYSTEM TERMINALS OF ECU


  1. CHECK WINDSHIELD WIPER RELAY ASSEMBLY

    A001Q5TN10

    1. Disconnect the F56 windshield wiper relay assembly connector.


      1. Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.

        Terminal No.

        (Symbol)

        		 Wiring Color Terminal Description Condition Specified Condition
        F56-2 (IG) - Body ground B - Body ground Power switch on (IG) signal (Power source circuit) Power switch on (IG) 11 to 14 V
        Power switch off Below 1 V
        F56-25 (W) - Body ground B - Body ground Front washer switch signal Front washer switch on Below 1 Ω
        Front washer switch off 10 kΩ or higher
        F56-8 (VR2) - F56-21 (VR1) W - G Adjusting volume signal Controlling sensitivity setting switch* changed 0 to 231 Ω
        F56-12 (E) - Body ground W-B - Body ground Body ground Always Below 1 Ω
        F56-16 (WIG) - Body ground B - Body ground Power source signal Power switch on (IG) 11 to 14 V
        Power switch off Below 1 V

        Tech Tips

        *: The rain sensor sensitivity can be adjusted by the controlling sensitivity setting switch.

        If the result is not as specified, there may be a malfunction in the wire harness.

    2. Reconnect the F56 windshield wiper relay assembly connector.


      1. Measure the resistance according to the value(s) in the table below.

        Terminal No.

        (Symbol)

        		 Wiring Color Terminal Description Condition Specified Condition
        F56-10 (+1) - Body ground G - Body ground Front wiper motor low speed signal Front wiper motor off Below 1 Ω

        Tech Tips

        If the result is not as specified, the windshield wiper relay assembly may be malfunctioning.

      2. Measure the voltage and check for pulses according to the value(s) in the table below.

        Terminal No.

        (Symbol)

        		 Wiring Color Terminal Description Condition Specified Condition
        F56-1 (+SM) - Body ground G - Body ground Front wiper motor position detection signal Front wiper motor in low or high operation Below 1 V ←→ 11 to 14 V
        Front wiper motor off Below 1 V
        F56-3 (C1) - F56-5 (CO) V - Y Front wiper switch AUTO signal Power switch on (IG), front wiper switch in AUTO Below 1 V
        Power switch on (IG), front wiper switch off 11 to 14 V
        F56-25 (W) - Body ground B - Body ground Front washer switch signal Power switch on (IG), front washer switch on Below 1 V
        Power switch on (IG), front washer switch off 11 to 14 V
        F56-10 (+1) - Body ground G - Body ground Front wiper motor low speed signal Front wiper motor in low operation 11 to 14 V
        F56-11 (+2) - Body ground W - Body ground Front wiper motor high speed signal Front wiper motor in high operation 11 to 14 V
        Front wiper motor off Below 1 V
        F56-14 (MPX1) - Body ground V - Body ground Rain sensor signal Power switch on (IG) Pulse generation
        F56-24 (SPD) - Body ground V - Body ground Vehicle speed signal Driving at approximately 20 km/h (12 mph) Pulse generation (See waveform 1)

        Tech Tips

        If the result is not as specified, the windshield wiper relay assembly may be malfunctioning.

      3. A001NVHE01

        Waveform 1 (Reference):

        Item Condition
        Tester Connection F56-24 (SPD) - Body ground
        Tool Setting 5 V/DIV., 20 ms./DIV.
        Vehicle Condition Driving at approximately 20 km/h (12 mph)

        Tech Tips

        When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.

  2. CHECK COMBINATION METER ASSEMBLY

    A001RDJE04

    1. Measure the voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      F4-17 (WLVL)* - Body ground LG - Body ground Washer fluid level signal Power switch on (IG), washer fluid level not low 11 to 14 V
      Power switch on (IG), washer fluid level low Below 1 V

      • *: w/ Washer Fluid Warning System

    2. Measure the waveform according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      F4-6 (+S) - Body ground V - Body ground Speed signal for other system (Output) Driving at approximately 20 km/h (12 mph) Pulse generation (See waveform 1)

      1. A001NVHE01

        Waveform 1 (Reference):

        Item Condition
        Tester Connection F4-6 (+S) - Body ground
        Tool Setting 5 V/DIV., 20 ms./DIV.
        Vehicle Condition Driving at approximately 20 km/h (12 mph)

        Tech Tips

        When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.

  3. HEADLIGHT ECU SUB-ASSEMBLY RH (for LED Headlight with Headlight Cleaner System)


    1. Disconnect the A17 headlight ECU sub-assembly RH connector.

      A001OVHN36

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Tech Tips

      Measure the values on the wire harness side with the connector disconnected.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      A17-4 (IG) - Body ground V - Body ground IG power supply Power switch off Below 1 V
      Power switch on (IG) 11 to 14 V
      A17-12 (GND) - Body ground W-B - Body ground Body ground Always Below 1 Ω

    3. Reconnect the A17 headlight ECU sub-assembly RH connector.

    4. Measure the voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      A17-7 (HLC) - Body ground W - Body ground Headlight cleaner motor operation signal Headlight cleaner motor not operating 11 to 14 V
      Headlight cleaner motor operating Below 1 V
      A17-18 (FRWA) - Body ground R - Body ground Front washer switch signal Power switch on (IG), front washer switch on 11 to 14 V
      Power switch on (IG), front washer switch off Below 1 V

  4. CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (for Halogen Headlight with Headlight Cleaner System)

    A001RUPC26
    *A Main Body ECU (Multiplex Network Body ECU) with 2 Connectors - -
    *1 Main Body ECU (Multiplex Network Body ECU) - -
    *a 2 Connectors - -
    A005N3LC31
    *A Main Body ECU (Multiplex Network Body ECU) with 1 Connector - -
    *1 Main Body ECU (Multiplex Network Body ECU) - -
    *a 1 Connector - -

    1. Measure the voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      3F-31 - Body ground G- Body ground Low beam headlight signal Light control switch in head position Below 1 V
      Light control switch off 4.2 V or higher

      If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may be malfunctioning.