REAR DOOR ADJUSTMENT

CAUTION / NOTICE / HINT

PROCEDURE

1. INSPECT REAR DOOR PANEL SUB-ASSEMBLY

   
   

   1. Check that the clearance measurements of areas "A" to "W" are within the standard ranges.

      

      Standard Clearance

      Area	Measurement	Area	Measurement
      A	3.3 to 6.7 mm (0.130 to 0.264 in.)	B	0.9 to 4.9 mm (0.035 to 0.193 in.)
      C	3.3 to 6.7 mm (0.130 to 0.264 in.)	D	1.8 to 5.8 mm (0.071 to 0.228 in.)
      E	3.3 to 6.7 mm (0.130 to 0.264 in.)	F	2.5 to 6.5 mm (0.098 to 0.256 in.)
      G	3.3 to 6.7 mm (0.130 to 0.264 in.)	H	2.3 mm (0.091 in.)
      I	3.3 to 7.3 mm (0.130 to 0.287 in.)	J	1.0 mm (0.039 in.)
      K	2.6 to 6.6 mm (0.102 to 0.260 in.)	L	0.7 mm (0.028 in.)
      M	2.6 to 5.6 mm (0.102 to 0.220 in.)	N	2.1 to 6.1 mm (0.083 to 0.240 in.)
      O	3.3 to 8.3 mm (0.130 to 0.327 in.)	P	-2.5 to 2.5 mm (-0.098 to 0.098 in.)
      Q	3.5 to 8.5 mm (0.138 to 0.335 in.)	R	7.5 to 11.5 mm (0.295 to 0.453 in.)
      S	-2.0 to 2.0 mm (-0.079 to 0.079 in.)	T	2.9 to 5.3 mm (0.114 to 0.209 in.)
      U	-1.2 to 1.2 mm (-0.047 to 0.047 in.)	V	2.4 to 6.4 mm (0.094 to 0.252 in.)
      W	-2.0 to 2.0 mm (-0.079 to 0.079 in.)	-	-

2. ADJUST REAR DOOR PANEL SUB-ASSEMBLY

   
   

   1. 

      Using SST, loosen the 4 hinge bolts on the vehicle body and adjust the door position.

      SST

      09812-00010

   2. Tighten the 4 hinge bolts on the vehicle body after adjustment.

      Torque:

      26 N*m  { 265 kgf*cm, 19 ft.*lbf }

   3. Loosen the 4 hinge bolts on the door and adjust the door position.

   4. Tighten the 4 hinge bolts on the door after adjustment.

      Torque:

      26 N*m  { 265 kgf*cm, 19 ft.*lbf }

   5. 

      Using a T40 "TORX" socket wrench, slightly loosen the 2 striker mounting screws.

   6. Using a brass bar and a hammer, hit the striker to adjust its position.

   7. Using a T40 "TORX" socket wrench, tighten the 2 striker mounting screws after adjustment.

      Torque:

      23 N*m  { 235 kgf*cm, 17 ft.*lbf }