ULTRASONIC SENSOR(for Rear) INSTALLATION

Info Added 2017-10-06

PROCEDURE


  1. INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER

    Tech Tips


    • Perform this procedure only when replacement of the rear center ultrasonic sensor retainer is necessary.

    • If a rear center ultrasonic sensor retainer has been removed, replace it with a new one.


    1. Clean the surface of the rear bumper cover.


      1. Remove any remaining double-sided tape from the rear bumper cover.

      2. Wipe off any adhesive residue with cleaner.

    2. A001R9DC01
      *a 18.4 to 18.8 mm (0.724 to 0.7401 in.)

      Cover the 2 sensor installation holes with a 18.4 to 18.8 mm (0.724 to 0.7401 in.) circular piece of tape.

    3. Using a brush or felt, apply primer or equivalent to the 2 rear center ultrasonic sensor retainers installation area.

      A001QSZC01
      *a Line - -
      A001P0O Primer - -

      Note


      • Use a clean brush or felt.

      • Do not touch the rear bumper assembly until the primer has dried.

    4. Peel off the release paper from the 2 rear center ultrasonic sensor retainers.

    5. Align the 2 rear center ultrasonic sensor retainers with the mark on the rear bumper cover and install it as shown in the illustration.

      A001NSDC01
      *a Line - -
      B0048V2 Press area - -

      Note

      The double-sided tape of a rear center ultrasonic sensor retainer will deteriorate if it is detached. Make sure to use a new rear center ultrasonic sensor retainer when reattachment is necessary.

      Tech Tips

      Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the rear center ultrasonic sensor retainer to the rear bumper cover. Confirm there is no clearance between the rear center ultrasonic sensor retainer and rear bumper cover.

  2. INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER

    Tech Tips


    • Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

    • If a rear corner ultrasonic sensor retainer has been removed, replace it with a new one.


    1. Clean the surface of the rear bumper cover.


      1. Remove any remaining double-sided tape from the rear bumper cover.

      2. Wipe off any adhesive residue with cleaner.

    2. A001R9DC01
      *a 26.2 to 26.6 mm (1.031 to 1.047 in.)

      Cover the 2 sensor installation hole with a 26.2 to 26.6 mm (1.031 to 1.047 in.) circular piece of tape.

    3. Using a brush or felt, apply primer or equivalent to the 2 rear corner ultrasonic sensor retainers installation area.

      Note


      • Use a clean brush or felt.

      • Do not touch the rear bumper assembly until the primer has dried.

      A001PTQC01
      *a Line - -
      A001P0O Primer - -

    4. Peel off the release paper 2 from the rear corner ultrasonic sensor retainers.

    5. Align the 2 rear corner ultrasonic sensor retainers with the mark on the rear bumper cover and install it as shown in the illustration.

      Note

      The double-sided tape of a rear corner ultrasonic sensor retainer will deteriorate if it is detached. Make sure to use a new rear corner ultrasonic sensor retainer when reattachment is necessary.

      A001PHWC01
      *a Line - -
      B0048V2 Press area - -

      Tech Tips

      Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the rear corner ultrasonic sensor retainer to the rear bumper cover. Confirm there is no clearance between the rear corner ultrasonic sensor retainer and rear bumper cover.

  3. INSTALL REAR SIDE ULTRASONIC SENSOR RETAINER

    Tech Tips


    • Perform this procedure only when replacement of the rear side ultrasonic sensor retainer is necessary.

    • If a rear side ultrasonic sensor retainer has been removed, replace it with a new one.


    1. Clean the surface of the rear bumper cover.


      1. Remove any remaining double-sided tape from the rear bumper cover.

      2. Wipe off any adhesive residue with cleaner.

    2. A001R9DC01
      *a 26.2 to 26.6 mm (1.031 to 1.047 in.)

      Cover the 2 sensor installation holes with a 26.2 to 26.6 mm (1.031 to 1.047 in.) circular piece of tape.

    3. Using a brush or felt, apply primer or equivalent to the 2 rear side ultrasonic sensor retainers installation area.

      A001QN5C01
      *a Line - -
      A001P0O Primer - -

      Note


      • Use a clean brush or felt.

      • Do not touch the rear bumper assembly until the primer has dried.

    4. Peel off the release paper from the 2 rear side ultrasonic sensor retainers.

    5. Align the 2 rear side ultrasonic sensor retainers with the mark on the rear bumper cover and install it as shown in the illustration.

      A001S40C01
      *a Line - -
      B0048V2 Press area - -

      Note

      The double-sided tape of a rear side ultrasonic sensor retainer will deteriorate if it is detached. Make sure to use a new rear side ultrasonic sensor retainer when reattachment is necessary.

      Tech Tips

      Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the rear side ultrasonic sensor retainer to the rear bumper cover. Confirm there is no clearance between the rear side ultrasonic sensor retainer and rear bumper cover.

  4. INSTALL REAR CENTER ULTRASONIC SENSOR

    Tech Tips

    The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


    1. A001O71C01
      B0048R7 Install in this Direction

      Engage the claws to install the rear center ultrasonic sensor as shown in the illustration.

    2. Connect the connector.

  5. INSTALL REAR CORNER ULTRASONIC SENSOR

    Tech Tips

    The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


    1. A001Q36C01
      B0048R7 Install in this Direction

      Engage the claws to install the rear corner ultrasonic sensor as shown in the illustration.

    2. Connect the connector.

  6. INSTALL REAR SIDE ULTRASONIC SENSOR

    Tech Tips

    The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


    1. A001QQAC01
      B0048R7 Install in this Direction

      Engage the claws to install the rear side ultrasonic sensor as shown in the illustration.

    2. Connect the connector.

  7. INSTALL REAR BUMPER ASSEMBLY

    Click here