ANTENNA CORD REMOVAL

Info Added 2017-10-06

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced the during antenna cord sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control)

Click here

Simple intelligent parking assist system*1
Toyota parking assist-sensor system*1
Pre-collision system
Initialize back door lock Power door lock control system

Click here

*1: When performing learning using the GTS.

Click here

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

B0048SV

Click here

PROCEDURE


  1. REMOVE INSTRUMENT PANEL SAFETY PAD

    Click here

  2. REMOVE NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY (for LHD)

    Click here

  3. REMOVE NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY (for RHD)

    Click here

  4. REMOVE ANTENNA CORD SUB-ASSEMBLY (for LHD)


    1. Disengage the clamps to remove the antenna cord sub-assembly.

      A001OV0

    2. Disconnect the connector.

  5. REMOVE ANTENNA CORD SUB-ASSEMBLY (for RHD)


    1. Disengage the clamps to remove the antenna cord sub-assembly.

      A001RLM

    2. Disconnect the connector.

  6. REMOVE ROOF HEADLINING

    Click here

  7. REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY


    1. Type A:


      1. Remove each adhesive tape from the roof headlining.

        A001P44C01
        *A w/ Digital Audio Broadcasting Antenna - -
        *a Notch *b Clamp
        B0048V2 Adhesive Tape B0048S8 Front

      2. Disengage the clamp and notch to remove the No. 2 antenna cord sub-assembly from the roof headlining.

    2. Type B:


      1. Remove each adhesive tape from the roof headlining.

        A001NTLC03
        *A w/ Digital Audio Broadcasting Antenna - -
        *a Notch *b Clamp
        B0048V2 Adhesive Tape B0048S8 Front

      2. Disengage the clamp and notch to remove the No. 2 antenna cord sub-assembly from the roof headlining.

  8. REMOVE NO. 5 ANTENNA CORD SUB-ASSEMBLY (w/ Digital Audio Broadcasting Antenna)


    1. A001R0N

      Disconnect the connector.

    2. Disengage the clamp to remove the No. 5 antenna cord sub-assembly.

  9. REMOVE NO. 3 ANTENNA CORD SUB-ASSEMBLY


    1. w/o FM Sub-antenna:


      1. A001OXI

        Disconnect the connector.

      2. Disengage the clamps.

      3. A001RYGC01
        *a Guide
        *b Clamp

        Remove the bolt.

      4. Disengage the clamp and guide to remove the No. 3 antenna cord sub-assembly.

    2. w/ FM Sub-antenna:


      1. A001RJS

        Disconnect the connector of the No. 4 antenna cord sub-assembly.

      2. A001OXI

        Disconnect the connector.

      3. Disengage the clamps.

      4. A001QE0C01
        *a Guide
        *b Clamp

        Disconnect the connector of the floor wire.

      5. Remove the bolt.

      6. Disengage the clamp and guide to remove the No. 3 antenna cord sub-assembly.

  10. REMOVE BACK DOOR TRIM UPPER PANEL ASSEMBLY (w/ FM Sub-antenna)

    Click here

  11. REMOVE NO. 4 ANTENNA CORD SUB-ASSEMBLY (w/ FM Sub-antenna)


    1. A001O9I

      Disconnect the connector.

    2. Disengage the clamp and 2 grommets to remove the No. 4 antenna cord sub-assembly.