HV BATTERY INSTALLATION

PROCEDURE


  1. INSTALL NO. 1 HYBRID BATTERY INTAKE DUCT

    Click here

  2. INSTALL NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY

    Click here

  3. INSTALL HV BATTERY JUNCTION BLOCK ASSEMBLY

    Click here

  4. INSTALL HYBRID BATTERY TERMINAL BLOCK

    Click here

  5. INSTALL BATTERY VOLTAGE SENSOR

    Click here

  6. INSTALL NO. 1 HV BATTERY SHIELD PANEL

    Click here

  7. INSTALL UPPER NO. 1 HYBRID BATTERY COVER SUB-ASSEMBLY

    CAUTION:

    Be sure to wear insulated gloves and protective goggles.


    1. A001NWUC03
      *a Bolt
      *b Nut

      Install the upper No. 1 hybrid battery cover sub-assembly to the HV battery with the 6 bolts and 5 nuts.

      Torque:
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

  8. INSTALL HV BATTERY

    CAUTION:

    Wear insulated gloves.


    1. A001QSKC02
      *a

      Bolt (A)

      (Bolt Length: 25 mm (0.984 in.))
      *b

      Bolt (B)

      (Bolt Length: 24 mm (0.945 in.))

      Install the HV battery to the vehicle with the 4 bolts (A) and bolt (B).

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

      Note


      • Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.

      • To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

      • Use cardboard or another similar material to protect the HV battery and vehicle body from damage.

      • Since the HV battery is very heavy, 2 people are needed to install it. When installing the HV battery, be careful not to damage the parts around it.

      • When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.

      • While lowering the HV battery into the vehicle, do not allow it to contact the vehicle.

      • As bolts with 2 different lengths are used, make sure to install each bolt to the correct position.

      • If the HV battery has been struck or dropped, replace it.

  9. CONNECT FLOOR WIRE

    CAUTION:

    Wear insulated gloves.


    1. Connect the battery voltage sensor connector.

    2. Engage the clamp.

  10. INSTALL NO. 1 HYBRID BATTERY EXHAUST DUCT


    1. Engage the claw to install the No. 1 hybrid battery exhaust duct to the HV battery.

    2. Install the clip.

  11. CONNECT FLOOR WIRE

    CAUTION:

    Wear insulated gloves.


    1. Connect the HV battery junction block assembly connector.

    2. Connect the electric vehicle battery plug assembly connector.

    3. Engage the clamp.

  12. CONNECT HV FLOOR UNDER WIRE

    CAUTION:

    Wear insulated gloves.


    1. Connect the shield ground to the HV battery.

    2. Connect the 2 HV battery junction block assembly connectors.

      Note

      Make sure that the connectors are connected securely.

  13. INSTALL NO. 1 HV BATTERY COVER PANEL RH

    CAUTION:

    Wear insulated gloves.


    1. A001R3SC02
      *1 Battery Cover Lock Striker
      *a Button
      *b Push

      Install the No. 1 HV battery cover panel RH to the HV battery with the 3 bolts and 2 nuts.

      Torque:
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

    2. Install the battery cover lock striker, then push the button to lock it.

  14. INSTALL BATTERY COOLING BLOWER ASSEMBLY

    Click here

  15. INSTALL REAR SEAT CUSHION LEG SUB-ASSEMBLY


    1. Install the rear seat cushion leg sub-assembly with the 6 bolts.

      Torque:
      16 N*m  { 163 kgf*cm, 12 ft.*lbf }

  16. INSTALL REAR UNDER COVER


    1. Engage the 2 guides to install the rear under cover to the rear seat cushion leg sub-assembly.

    2. Engage the 2 clips.

  17. INSTALL REAR UNDER SIDE COVER LH

    Click here

  18. INSTALL REAR DOOR SCUFF PLATE LH

    Click here

  19. INSTALL REAR UNDER SIDE COVER RH

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  20. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  21. INSTALL REAR SEAT CUSHION LOCK HOOK

    Click here

  22. INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY

    Click here

  23. INSTALL SERVICE PLUG GRIP

    Click here

  24. PERFORM BATTERY STATUS INFO UPDATE

    Click here