SFI SYSTEM, Diagnostic DTC:P044313

DTC Code DTC Name
P044313 Evaporative Emission System Purge Control Valve "A" Circuit Open

DESCRIPTION

To reduce hydrocarbon (HC) emissions, evaporated fuel from the fuel tank is routed through a canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signals to the purge VSV so that the intake amount of evaporated fuel routed to the cylinders is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P044313 Evaporative Emission System Purge Control Valve "A" Circuit Open

Both of the following conditions are met for 10 seconds or more (1 trip detection logic):


  • The purge VSV operation duty signal is 5 to 95%.

  • The target control value and actual control value do not match.

  • Open or short in purge VSV circuit

  • Purge VSV

  • ECM

 Comes on DTC stored SAE Code: P0443

CONFIRMATION DRIVING PATTERN

A001OFRE66

  1. Connect the GTS to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the power switch off and wait for at least 30 seconds.

  6. Turn the power switch on (IG).

  7. Turn the GTS on.

  8. Put the engine in Inspection Mode (Maintenance Mode).

    Click here

  9. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

    Tech Tips

    The A/C switch and all accessories should be off.

  10. Idle the engine for 15 minutes or more [B].

    Tech Tips

    Check the Data List item "EVAP (Purge) VSV". When the value of this item is between 5 and 95%, the judgment will be performed.

  11. Enter the following menus: Powertrain / Engine / Trouble Codes [C].

  12. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  13. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  14. Input the DTC: P044313.

  15. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result is NORMAL, the system is normal.

    • If the judgment result is ABNORMAL, the system is malfunctioning.

    • If the judgment result is INCOMPLETE or N/A, perform steps [D] and [E].

  16. With the engine running, drive the vehicle at a constant speed between 40 and 60 km/h (25 and 37 mph) for 10 minutes or more [D].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    Tech Tips

    If the engine stops, further depress the accelerator pedal to restart the engine.

  17. Enter the following menus: Powertrain / Engine / Trouble Codes [E].

  18. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  19. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  20. Input the DTC: P044313.

  21. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result is NORMAL, the system is normal.

    • If the judgment result is ABNORMAL, the system is malfunctioning.

WIRING DIAGRAM

A001RILE04

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following procedure.

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EVAP PURGE VSV)

    A001S59C01
    *a VSV is on
    *b VSV is off

    1. Disconnect the fuel vapor feed hose assembly (canister side) of the purge VSV.

    2. Connect the GTS to the DLC3.

    3. Turn the power switch on (IG).

    4. Turn the GTS on.

    5. Put the engine in Inspection Mode (Maintenance Mode).

      Click here


      Powertrain > Hybrid Control > Utility
      Tester Display
      Inspection Mode

    6. Start the engine.

    7. Enter the following menus: Powertrain / Engine / Active Test / Activate the EVAP Purge VSV.


      Powertrain > Engine > Active Test
      Tester Display
      Activate the EVAP Purge VSV

    8. When the purge VSV is operated using the GTS, check whether the port of the purge VSV applies suction your finger.

      OK
      GTS Operation Specified Condition
      ON Purge VSV port applies suction to finger
      OFF Purge VSV port applies no suction to finger

      Tech Tips

      Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

      Result
      Proceed to
      OK
      NG

    OK

    CHECK FOR INTERMITTENT PROBLEMS Click here

    NG

  2. INSPECT PURGE VSV


    1. Inspect the purge VSV.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE PURGE VSV Click here

    OK

  3. CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)

    A001PAKC09
    *a

    Front view of wire harness connector

    (to Purge VSV)

    1. Disconnect the purge VSV connector.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      C12-2 - Body ground Power switch on (IG) 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - PURGE VSV)

    OK

  4. CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)


    1. Disconnect the C12 purge VSV connector.

    2. Disconnect the C63 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C12-1 - C63-33 (PRG) Always Below 1 Ω
      C12-1 or C63-33 (PRG) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR