BLOCKING SYSTEM TERMINALS OF ECU


  1. CHECK TELEPHONE TRANSCEIVER ASSEMBLY

    A01W4LYE02

    1. Disconnect the H102 telephone transceiver assembly connector.

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      H102-6 (IG2) - H102-9 (E) LG - W-B Ignition power supply Engine switch on (IG) 9 to 16 V
      H102-12 (+B) - H102-9 (E) Y - W-B +B power supply Always 9 to 16 V
      H102-9 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

      • If the result is not as specified, there may be a malfunction on the wire harness side.

    3. Reconnect the H102 telephone transceiver assembly connector.

    4. Measure the voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      H102-1 (BLK1) - H102-9 (E) LG - W-B ID code box (immobiliser code ECU) communication input Engine switch off 11 to 14 V
      H102-1 (BLK1) - H102-9 (E) LG - W-B ID code box (immobiliser code ECU) communication input Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

      Pulse generation

      (See waveform 1)
      H102-2 (BLK4) - H102-9 (E) SB - W-B ID code box (immobiliser code ECU) communication output Engine switch off Below 1 V
      H102-2 (BLK4) - H102-9 (E) SB - W-B ID code box (immobiliser code ECU) communication output Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

      Pulse generation

      (See waveform 2)
      H102-7 (BLK2) - H102-9 (E) G - W-B ECM communication output Engine switch off Below 1 V
      H102-7 (BLK2) - H102-9 (E) G - W-B ECM communication output Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

      Pulse generation

      (See waveform 1)
      H102-8 (BLK3) - H102-9 (E) SB - W-B ECM communication input Engine switch off Below 1 V
      H102-8 (BLK3) - H102-9 (E) SB - W-B ECM communication input Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

      Pulse generation

      (See waveform 2)

      • If the result is not as specified, the telephone transceiver assembly may have a malfunction.

    5. Inspect using an oscilloscope.

      Note

      The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


      1. Waveform 1 (Reference)

        A01W4CVE01
        Text in Illustration
        *a Approximately 160 ms *b Approximately 270 ms
        Measurement Condition
        Item Content
        Tester Connection

        • H102-1 (BLK1) - H102-9 (E)

        • H102-7 (BLK2) - H102-9 (E)
        Tool Setting 2 V/DIV., 500 ms./DIV.
        Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

      2. Waveform 2 (Reference)

        A01W1C8E01
        Text in Illustration
        *a Approximately 160 ms *b Approximately 270 ms
        Measurement Condition
        Item Content
        Tester Connection

        • H102-2 (BLK4) - H102-9 (E)

        • H102-8 (BLK3) - H102-9 (E)
        Tool Setting 2 V/DIV., 500 ms./DIV.
        Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

  2. CHECK ID CODE BOX (IMMOBILISER CODE ECU)


    1. Disconnect the H15 ID code box (immobiliser code ECU) connector.

      A01W26BE02

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Tester Connection (Symbol) Wiring Color Terminal Description Condition Specified Condition
      H15-1 (+B) - H15-5 (GND) R - W-B +B power supply Always 11 to 14 V
      H15-5 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

      • If the result is not as specified, there may be a malfunction in the wire harness.

    3. Reconnect the H15 ID code box (immobiliser code ECU) connector.

    4. Measure the voltage according to the value(s) in the table below.

      Tester Connection (Symbol) Wiring Color Terminal Description Condition Specified Condition
      H15-3 (EFII) - H15-5 (GND) LG - W-B ECM input signal Engine switch off 11 to 14 V
      H15-3 (EFII) - H15-5 (GND) LG - W-B ECM input signal Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected

      Pulse generation

      (See waveform 1)
      H15-4 (EFIO) - H15-5 (GND) SB - W-B ECM output signal Engine switch off Below 1 V
      H15-4 (EFIO) - H15-5 (GND) SB - W-B ECM output signal Engine switch on (IG)

      Pulse generation

      (See waveform 2)

      • If the result is not as specified, the ID code box (immobiliser code ECU) may have a malfunction.

    5. Inspect using an oscilloscope.


      1. Waveform 1 (Reference)

        A01W4CVE01
        Text in Illustration
        *a Approximately 160 ms *b Approximately 270 ms
        Item Content
        Tester Connection H15-3 (EFII) - H15-5 (GND)
        Tool Setting 5 V/DIV., 500 ms./DIV.
        Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected

      2. Waveform 2 (Reference)

        A01W1C8E01
        Text in Illustration
        *a Approximately 160 ms *b Approximately 270 ms
        Item Content
        Tester Connection H15-4 (EFIO) - H15-5 (GND)
        Tool Setting 10 V/DIV., 100 ms./DIV.
        Condition Engine switch on (IG)

  3. CHECK ECM

    A01W36YE02

    Tech Tips

    The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage or resistance for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.

    Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
    D23-49 (E1) - Body ground BR - Body ground Ground Always Below 1 Ω
    A22-1 (BATT) - D23-49 (E1) GR - BR +B power supply Always 11 to 14 V
    A22-2 (+B) - D23-49 (E1) P - BR +B power supply Engine switch on (IG) 11 to 14 V
    A22-3 (+B2) - D23-49 (E1) LG - BR +B power supply Engine switch on (IG) 11 to 14 V
    A22-30 (IMO) - D23-49 (E1) G - BR Certification ECU (smart key ECU assembly) communication input Engine switch off Below 1 V
    A22-30 (IMO) - D23-49 (E1) G - BR Certification ECU (smart key ECU assembly) communication input Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

    Pulse generation

    (See waveform 1)
    A22-31 (IMI) - D23-49 (E1) Y - BR Certification ECU (smart key ECU assembly) communication output Engine switch off Below 1 V
    A22-31 (IMI) - D23-49 (E1) Y - BR Certification ECU (smart key ECU assembly) communication output Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

    Pulse generation

    (See waveform 2)

    1. Inspect using an oscilloscope.

      Note

      The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


      1. Waveform 1 (Reference)

        A01W4CVE01
        Text in Illustration
        *a Approximately 160 ms *b Approximately 270 ms
        Measurement Condition
        Item Content
        Tester Connection A22-30 (IMO) - D23-49 (E1)
        Tool Setting 2 V/DIV., 500 ms./DIV.
        Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

      2. Waveform 2 (Reference)

        A01W1C8E01
        Text in Illustration
        *a Approximately 160 ms *b Approximately 270 ms
        Measurement Condition
        Item Content
        Tester Connection A22-31 (IMI) - D23-49 (E1)
        Tool Setting 2 V/DIV., 500 ms./DIV.
        Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected