CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) Front Camera Module Communication Stop Mode

DESCRIPTION

Detection Item Symptom Trouble Area
Front Camera Module Communication Stop Mode

Either condition is met:


  • "Front Camera Module" is not displayed on the CAN Bus Check screen of the Techstream Click here.

  • Communication system DTCs (DTCs that start with U) that correspond to "Front Camera Module Communication Stop Mode" in "DTC Combination Table" are output Click here.

  • Forward recognition camera branch line or connector

  • Power source circuit of forward recognition camera

  • Forward recognition camera ground circuit

  • Forward recognition camera

WIRING DIAGRAM

A01W5IZE03

CAUTION / NOTICE / HINT

Note


  • Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output Click here.

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

  • DTC check procedure: Turn the engine switch on (IG), turn the LDA main switch on and wait for 52 seconds or more.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed Click here.

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Tech Tips


  • Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE


  1. CHECK FOR OPEN IN CAN BUS LINES (FORWARD RECOGNITION CAMERA BRANCH LINE)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. A01W1O3E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Forward Recognition Camera)

      Disconnect the T12 forward recognition camera connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Value
      T12-5 (CA1P) - T12-11 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

    NG

    REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (FORWARD RECOGNITION CAMERA)

    OK

  2. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)


    1. A01W1DHE04
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Forward Recognition Camera)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Value
      T12-10 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω

    2. Reconnect the cable to the negative (-) battery terminal.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Value
      T12-7 (IGB) - Body ground Engine switch on (IG) 11 to 14 V
      Result
      Result Proceed to
      OK A
      NG (except 6AR-FSE) B
      NG (for 6AR-FSE) C

    A

    REPLACE FORWARD RECOGNITION CAMERA Click here

    B

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

    C

    CHECK FOR BACKUP BOOST CONVERTER CIRCUIT Click here