CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) ECM Communication Stop Mode

DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode

Either condition is met:


  • "ECM (Engine)" is not displayed on the CAN Bus Check screen of the GTS Click here

  • Communication system DTCs (DTCs that start with U) that correspond to "ECM Communication Stop Mode" in "DTC Combination Table" are output Click here


  • Power source circuit of ECM

  • ECM main line or connector

  • ECM ground circuit

  • ECM

WIRING DIAGRAM

A01VZ5WE08
A01VZ5WE09
A01VZ5WE10
A01W3CHE05
A01W3CHE06

CAUTION / NOTICE / HINT

Note


  • Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output Click here.

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

  • DTC check procedure: Drive the vehicle at a speed of 36 km/h (22 mph) or more for 5 minutes or more.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed Click here.

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Tech Tips


  • Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE


  1. CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. A01W5R4E02
      Text in Illustration
      *1 for 2GR-FE
      *2 for 2AR-FE
      *3 for 6AR-FSE
      *a

      Front view of wire harness connector

      (to ECM)

      Disconnect the A22 A64 or A75 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (for 2GR-FE)
      Tester Connection Condition Specified Condition
      A22-13 (CANH) - A22-26 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Standard Resistance (for 2AR-FE)
      Tester Connection Condition Specified Condition
      A64-13 (CANH) - A64-26 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Standard Resistance (for 6AR-FSE)
      Tester Connection Condition Specified Condition
      A75-13 (CANH) - A75-26 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

    NG

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM MAIN LINE)

    OK

  2. CHECK ECM POWER SOURCE CIRCUIT


    1. Check the ECM power source circuit.

      for 2GR-FE: Click here

      for 2AR-FE: Click here

      for 6AR-FSE: Click here

      Result
      Result Proceed to
      OK (for 2GR-FE) A
      OK (for 2AR-FE) B
      OK (for 6AR-FSE) C
      NG D

    A

    REPLACE ECM Click here

    B

    REPLACE ECM Click here

    C

    REPLACE ECM Click here

    D

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)