PARKING BRAKE ASSEMBLY REASSEMBLY

PROCEDURE


  1. APPLY HIGH TEMPERATURE GREASE


    1. A01W17O

      Apply high temperature grease to the areas of the parking brake plate which make contact with the shoe as shown in the illustration.

      Text in Illustration
      B001OGU High Temperature Grease

  2. INSTALL PARKING BRAKE SHOE HOLD DOWN SPRING PIN


    1. Install the 2 parking brake shoe hold down spring pins.

  3. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Lower Side)


    1. Install the parking brake shoe return tension spring to the No. 2 parking brake shoe assembly.

  4. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. Install the No. 1 parking brake shoe assembly to the parking brake shoe return tension spring.

  5. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET


    1. A01W30H

      Apply high temperature grease to the parking brake shoe adjusting screw set as shown in the illustration.

      Text in Illustration
      B001OGU High Temperature Grease

    2. Install the parking brake shoe adjusting screw set to the No. 1 parking brake shoe assembly and No. 2 parking brake shoe assembly.

  6. INSTALL PARKING BRAKE SHOE LEVER


    1. A01VZLX

      Using needle-nose pliers, install the parking brake shoe lever to the No. 3 parking brake cable assembly.

    2. A01W4OL

      Apply high temperature grease to the areas of the parking brake shoe lever which make contact with the No. 2 parking brake shoe assembly.

      Text in Illustration
      B001OGU High Temperature Grease
    3. A01W03B

      Install the parking brake shoe lever to the No. 2 parking brake shoe assembly.

    4. Expand the No. 1 and No. 2 parking brake shoe assemblies outward by hand and fit them to the parking brake plate.

      Note

      Make sure that the parking brake shoe lever does not separate from the No. 2 parking brake shoe assembly.

  7. INSTALL PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING (for Rear Side)


    1. A01W14ZE01

      Using SST, install the parking brake shoe hold down compression spring.

      SST
      09718-00011

  8. INSTALL PARKING BRAKE SHOE STRUT


    1. Install the parking brake shoe strut.

    2. A01W43V

      Install the No. 1 parking brake shoe assembly.

  9. INSTALL PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING (for Front Side)


    1. A01W0MNE01

      Using SST, install the parking brake shoe hold down compression spring.

      SST
      09718-00011

  10. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Rear Side)


    1. A01VZ4N

      Apply a small amount of high temperature grease to the areas shown in the illustration.

      Text in Illustration
      B001OGU High Temperature Grease

    2. Install the parking brake shoe return tension spring.

  11. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Front Side)


    1. Install the parking brake shoe return tension spring.

  12. CHECK PARKING BRAKE INSTALLATION


    1. Check that each part is installed properly.

      A01W438E01
      Text in Illustration
      *A LH Side *B RH Side
      B001O8N Front of the Vehicle - -

      Note

      There should be no oil or grease on the friction surfaces of the shoe linings or discs.

  13. INSTALL REAR DISC

    Click here

  14. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

  15. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

    Click here

  16. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL

    Click here

  17. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1049 kgf*cm, 76 ft.*lbf }