PARKING BRAKE CABLE INSTALLATION

PROCEDURE

1. INSTALL NO. 2 PARKING BRAKE CABLE CLAMP

   
   

   1. Install a new No. 2 parking brake cable clamp to the No. 3 parking brake cable assembly.

2. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

   
   

   1. Install the No. 3 parking brake cable assembly with the 4 bolts and nut.

      

      Torque:

      Bolt (A) and Nut

      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Bolt (B)

      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

   2. Install the No. 3 parking brake cable assembly with the bolt.

      Torque:

      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

   3. Install the clip to the No. 3 parking brake cable assembly.

3. INSTALL NO. 2 FLOOR UNDER COVER (for LH Side)

   Click here

4. INSTALL NO. 1 FLOOR UNDER COVER (for RH Side)

   Click here

5. INSTALL PARKING BRAKE SHOE LEVER

   Click here

6. INSTALL FRONT NO. 2 FLOOR HEAT INSULATOR (for 2AR-FE, 6AR-FSE)

   
   

   1. Install the front No. 2 floor heat insulator with the 3 nuts.

      Torque:

      4.9 N*m  { 50 kgf*cm, 43 in.*lbf }

7. INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 2AR-FE)

   Click here

8. INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) (for 6AR-FSE)

   Click here

9. INSTALL NO. 4 PARKING BRAKE CABLE ASSEMBLY

   
   
   1. 

      Text in Illustration

      *1	No. 4 Parking Brake Cable Assembly
      *2	Rubber Boot
      *3	Parking Brake Equalizer

      Install the No. 4 parking brake cable assembly to the parking brake equalizer.

   2. Slide the parking brake equalizer and rubber boot as shown in the illustration.

      Note

      Make sure that the rubber boot is securely inserted into the groove of the No. 4 parking brake cable assembly.

   3. 

      Text in Illustration

      *1	Parking Brake Equalizer
      *2	No. 2 Parking Brake Cable Assembly
      *3	No. 3 Parking Brake Cable Assembly
      *4	No. 4 Parking Brake Cable Assembly

      Connect the No. 3 parking brake cable assembly to the parking brake equalizer.

   4. Connect the No. 2 parking brake cable assembly to the parking brake equalizer.

10. INSTALL NO. 4 CROSS MEMBER FLOOR REINFORCEMENT SUB-ASSEMBLY

    
    

    1. Install the No. 4 cross member floor reinforcement sub-assembly with the 8 bolts.

       Torque:

       19 N*m  { 189 kgf*cm, 14 ft.*lbf }

    2. Install the floor carpet.

11. INSTALL NO. 2 CONSOLE BOX MOUNTING BRACKET

    
    

    1. Install the No. 2 console box mounting bracket with the 2 bolts.

    2. Engage the 2 clamps to install the wire harness to the No. 2 console box mounting bracket.

12. INSTALL FRONT FLOOR CAUTION PLATE COVER

    Click here

13. INSTALL FLOOR CARPET HOOK

    Click here

14. INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET

    Click here

15. INSTALL AUDIO AMPLIFIER COVER

    Click here

16. INSTALL TELEMATICS TRANSCEIVER (w/ Telematics Transceiver except G-BOOK)

    Click here

17. INSTALL TELEMATICS TRANSCEIVER WITH MAYDAY BATTERY (w/ Telematics Transceiver for G-BOOK)

    Click here

18. INSTALL AUDIO AMPLIFIER COVER (w/ Telematics Transceiver)

    Click here

19. INSTALL FRONT SEAT ASSEMBLY LH

    Click here

20. INSTALL FRONT SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

21. INSTALL CENTER PILLAR LOWER GARNISH LH

    Click here

22. INSTALL REAR DOOR SCUFF PLATE LH

    Click here

23. INSTALL CENTER PILLAR LOWER GARNISH RH

    Click here

24. INSTALL REAR DOOR SCUFF PLATE RH

    Click here

25. INSTALL COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

26. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

27. INSTALL NO. 1 PARKING BRAKE CABLE ASSEMBLY (for LHD)

    
    

    1. Pass the No. 1 parking brake cable assembly through the parking brake pedal assembly.

    2. Install the clip to the No. 1 parking brake cable assembly.

    3. Temporarily install the adjusting nut.

    4. 

       Bend the parking brake pedal claw.

28. INSTALL NO. 1 PARKING BRAKE CABLE ASSEMBLY (for RHD)

    
    

    1. Pass the No. 1 parking brake cable assembly through the parking brake pedal assembly.

    2. Install the clip to the No. 1 parking brake cable assembly.

    3. Temporarily install the adjusting nut.

    4. 

       Bend the parking brake pedal claw.

29. INSTALL PARKING BRAKE PEDAL SUB-ASSEMBLY (for LHD)

    Click here

30. INSTALL PARKING BRAKE PEDAL SUB-ASSEMBLY (for RHD)

    Click here