DIFFERENTIAL OIL SEAL REPLACEMENT

PROCEDURE


  1. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

    Click here

  2. REMOVE ENGINE UNDER COVER LH

    Click here

  3. REMOVE FRONT FENDER APRON SEAL LH

    Click here

  4. DRAIN AUTOMATIC TRANSAXLE FLUID


    1. A01W267

      Remove the refill plug and gasket from the rear transaxle cover sub-assembly.

    2. A01W558

      Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle oil pan sub-assembly.

    3. A01W08LE03
      Text in Illustration
      *1 No. 1 Transmission Oil Filler Tube
      *a 6 mm Hexagon Socket Wrench
      *b Overflow Plug Hole

      Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle oil pan sub-assembly.

    4. Drain automatic transaxle fluid from the automatic transaxle assembly.

    5. A01W08LE03
      Text in Illustration
      *1 No. 1 Transmission Oil Filler Tube
      *a 6 mm Hexagon Socket Wrench
      *b Overflow Plug Hole

      Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the automatic transaxle oil pan sub-assembly.

      Torque:
      0.8 N*m  { 8 kgf*cm, 7 in.*lbf }
    6. A01W558

      Using a 6 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the automatic transaxle oil pan sub-assembly.

      Tech Tips

      Reuse the old gasket as the overflow plug will be removed again to adjust the fluid level.

    7. A01W267

      Temporarily install the gasket and refill plug to the automatic transaxle assembly.

      Tech Tips

      Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.

  5. REMOVE FRONT DRIVE SHAFT ASSEMBLY

    Click here

  6. REMOVE TRANSAXLE CASE OIL SEAL


    1. A01W269E05

      Using SST, remove the transaxle case oil seal from the transaxle case sub-assembly.

      SST
      09308-00010

      Note

      Be careful not to damage the transaxle case sub-assembly.

  7. REMOVE DRIVE SHAFT BEARING BRACKET

    Click here

  8. REMOVE FRONT TRANSAXLE CASE OIL SEAL


    1. A01VZCJE04

      Using SST, remove the front transaxle case oil seal from the transaxle housing.

      SST
      09308-00010

      Note

      Be careful not to damage the transaxle housing.

  9. INSTALL FRONT TRANSAXLE CASE OIL SEAL


    1. A01VZPQE02
      Text in Illustration
      *a Depth

      Using SST and a hammer, install a new front transaxle case oil seal to the transaxle housing.

      SST
      09316-60011   ( 09316-00011 )
      Standard Depth
      -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

      Note


      • Make sure that the front transaxle case oil seal is installed in the correct direction.

      • Do not damage the lip of the front transaxle case oil seal.

    2. Coat the lip of the front transaxle case oil seal with MP grease.

  10. INSTALL DRIVE SHAFT BEARING BRACKET

    Click here

  11. INSTALL TRANSAXLE CASE OIL SEAL


    1. A01W5QXE02
      Text in Illustration
      *a Depth

      Using SST and a hammer, install a new transaxle case oil seal to the transaxle case sub-assembly.

      SST
      09316-10010
      09950-70010   ( 09951-07150 )
      Standard Depth
      -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

      Note


      • Make sure that the transaxle case oil seal is installed in the correct direction.

      • Do not damage the lip of the transaxle case oil seal.

    2. Coat the lip of the transaxle case oil seal with MP grease.

  12. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH

    Click here

  13. INSTALL FRONT DRIVE SHAFT ASSEMBLY

    Click here

  14. ADD AUTOMATIC TRANSAXLE FLUID

    Click here

  15. INSTALL FRONT FENDER APRON SEAL LH

    Click here

  16. INSTALL ENGINE UNDER COVER LH

    Click here

  17. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

    Click here