AUTOMATIC TRANSAXLE SYSTEM REGISTRATION

CAUTION / NOTICE / HINT

Note


  • When the automatic transaxle assembly is replaced, the transaxle compensation code must be input into the ECM (proceed to Procedure 1). After the automatic transaxle assembly is reinstalled, the Quick Response (QR) code label will be positioned where the code cannot be read. Therefore, before reinstalling the automatic transaxle assembly, record the transaxle compensation codes or input it using the GTS.

  • When the ECM is replaced, the existing transaxle compensation codes must be input into the new ECM (proceed to Procedure 2).

PROCEDURE


  1. INPUT TRANSAXLE COMPENSATION CODE INTO ECM (Procedure 1)

    Note

    Transaxle compensation codes are unique, 60-digit alphanumeric values printed on a QR code label on the transaxle. If an incorrect transaxle compensation code is input into the ECM, shift shock may occur.


    1. A01W0L6E02
      Text in Illustration
      *1 QR Code Label
      *a Transaxle Compensation Code

      Record the transaxle compensation code specified on the QR code label.

      Tech Tips

      The transaxle compensation code is printed on the QR code label.

    2. Make sure the shift lever is in P or N.

    3. Connect the GTS to the DLC3.

    4. Turn the engine switch on (IG).

      Note

      Do not start the engine.

    5. Turn the GTS on.

    6. Enter the following menus: Powertrain / Transmission / Utility / A/T Code Registration.

    7. Select "Set Compensation Code".

    8. Register the transaxle compensation code.


      1. Press "Input".

      2. Manually input the transaxle compensation code. The code is a 60-digit alphanumeric value printed on the QR code label. After inputting the code, press "OK".

    9. Check that the transaxle compensation code displayed on the screen is correct by comparing it with the 60-digit alphanumeric value on the QR code label.

      Note

      If an incorrect transaxle compensation code is registered into the ECM, shift shock may occur.

    10. Press "NEXT" to register the transaxle compensation code to the ECM.

      Tech Tips


      • If the registration process fails, the transaxle compensation code may be incorrect. Check the attempted transaxle compensation code.

      • If the attempted transaxle compensation code is correct, a problem with the wire harness or a bad connection with the DLC3 may cause registration failure. Check the wire harness and the DLC3 connection. If no problem is found, the ECM may be malfunctioning. Check the ECM and repeat this operation.

    11. Press "EXIT".

  2. TRANSFER TRANSAXLE COMPENSATION CODE (Procedure 2)

    Note

    Transaxle compensation codes are 60-digit alphanumeric values printed on a QR code label on the transaxle. If an incorrect transaxle compensation code is input into the ECM, shift shock may occur.

    Tech Tips

    The following operation is available for use when the ECM that is being replaced can still transmit its registered transaxle compensation code to the GTS.


    1. Make sure the shift lever is in P or N.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG).

      Note

      Do not start the engine.

    4. Turn the GTS on.

      Tech Tips

      The transaxle compensation code is printed on the QR code label.

    5. Read the transaxle compensation code.


      1. Enter the following menus: Powertrain / Transmission / Utility / A/T Code Registration.

      2. Select "Read Compensation Code".

      3. Press "Save".

      4. Press "Save" or "Overwrite".

        Note

        Do not use the code printed on the transaxle QR code label even if the transaxle compensation code cannot be read using the GTS. The code printed on an in-service transaxle may not match its current characteristics. Replace the ECM with a new one and perform a road test to allow the ECM to learn the transaxle characteristics.

        Tech Tips

        Press "Overwrite".

      5. Press "EXIT".

      6. Turn the engine switch off.

    6. Replace the ECM.

    7. Register the transaxle compensation code.


      1. Turn the engine switch on (IG).

      2. Turn the GTS on.

      3. Enter the following menus: Powertrain / Transmission / Utility / A/T Code Registration.

      4. Select "Set Compensation Code".

      5. Press "Open".

      6. Press "Open" again to proceed.

      7. Press "Exit".