OIL AND OIL FILTER REPLACEMENT

CAUTION / NOTICE / HINT

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water or waterless hand cleaner to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.

  • In order to preserve the environment, used oil and used oil filters must be disposed of at designated disposal sites.

PROCEDURE


  1. DRAIN ENGINE OIL


    1. Remove the oil filler cap.

    2. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

    3. Clean the oil pan drain plug.

    4. Install the oil pan drain plug with a new gasket.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

  2. REMOVE OIL FILTER CAP ASSEMBLY


    1. A01W203E06
      Text in Illustration
      *1 Pipe
      *2 Hose

      Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

    2. A01W1BC

      Remove the oil filter drain plug from the oil filter cap assembly.

    3. A01W4HWE09
      Text in Illustration
      *1 Valve
      *2 Oil Filter Cap Assembly
      *3 O-ring
      *4 Pipe

      Insert the pipe with the hose into the oil filter cap assembly.

      Note

      If the O-ring is removed with the oil filter drain plug, install the O-ring together with the pipe.

      Tech Tips

      Use a container to catch the draining oil.

    4. A01W2G3

      Check that the engine oil is drained from the oil filter. Then disconnect the pipe as shown in the illustration and remove the O-ring.

    5. A01W29XE02
      Text in Illustration
      *1 Oil Filter Bracket Clip

      Using SST, remove the oil filter cap assembly.

      SST
      09228-06501

      Note

      Do not remove the oil filter bracket clip.

    6. A01W219E12
      Text in Illustration
      *1 Oil Filter Element
      *2 Oil Filter Cap Assembly
      *3 O-ring

      Remove the oil filter element and O-ring from the oil filter cap assembly.

      Note

      Be sure to remove the O-ring by hand, without using any tools, to prevent damage to the O-ring groove.

  3. INSTALL OIL FILTER CAP ASSEMBLY


    1. Clean the inside of the oil filter cap assembly, threads and O-ring groove.

    2. A01W31VE15
      Text in Illustration
      *1 O-ring
      *a CORRECT
      *b INCORRECT

      Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap assembly.

      Note


      • Be sure to install the O-ring in the proper location, otherwise oil may leak.

      • Do not twist the O-ring.

    3. Set a new oil filter element into the oil filter cap assembly.

    4. Remove all dirt and foreign matter from the installation surface and the inside of the oil filter cap assembly on the engine side.

    5. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap assembly.

      Note

      Make sure that the O-ring does not get caught between the parts.

    6. A01W5AOE05
      Text in Illustration
      *1 Oil Filter Cap Assembly
      *2 O-ring
      *3 Oil Filter Bracket
      *a No Gap

      Using SST, tighten the oil filter cap assembly.

      SST
      09228-06501
      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

      Note

      After tightening the oil filter cap assembly, make sure that there is no gap and that the O-ring is not protruding.

    7. A01W1KLE06
      Text in Illustration
      *1 O-ring

      Apply a small amount of engine oil to a new O-ring, and install it to the oil filter cap assembly.

      Note

      Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap assembly.

    8. Install the oil filter drain plug.

      Torque:
      13 N*m  { 127 kgf*cm, 10 ft.*lbf }

      Note

      Be careful that the O-ring does not get caught between any surrounding parts.

  4. ADD ENGINE OIL


    1. Add new oil.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)

      • API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil

      • 0W-20

      • 5W-20

      • 5W-30

      • 10W-30
      API grade SL, SM or SN multigrade engine oil

      • 15W-40

      • 20W-50
      Standard Capacity
      Item Specified Condition
      Drain and refill (with oil filter change) 4.4 liters (4.6 US qts, 3.9 Imp. qts)
      Drain and refill (without oil filter change) 4.0 liters (4.2 US qts, 3.5 Imp. qts)
      Dry fill 5.3 liters (5.6 US qts, 4.7 Imp. qts)

    2. Install the oil filler cap.

  5. INSPECT FOR OIL LEAK

  6. INSPECT ENGINE OIL LEVEL

    Click here