EXHAUST MANIFOLD INSTALLATION

PROCEDURE


  1. INSTALL NO. 1 MANIFOLD CONVERTER INSULATOR


    1. Install the No. 1 manifold converter insulator with the 4 bolts.

      Torque:
      14 N*m  { 138 kgf*cm, 10 ft.*lbf }

  2. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    1. Install the No. 2 exhaust manifold heat insulator with the 2 bolts.

      Torque:
      14 N*m  { 138 kgf*cm, 10 ft.*lbf }

  3. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY


    1. Set a new gasket to the cylinder head sub-assembly.

    2. Temporarily install the exhaust manifold converter sub-assembly with the 5 nuts.

    3. Temporarily install the No. 2 manifold stay and manifold stay with the 2 bolts and 2 nuts.

    4. A01W3F2E02

      Tighten the 5 nuts in the sequence shown in the illustration.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

  4. INSTALL AIR FUEL RATIO SENSOR

    Click here

  5. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    1. Install the No. 1 exhaust manifold heat insulator with the 4 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  6. INSTALL NO. 2 MANIFOLD STAY


    1. Install the No. 2 manifold stay with the bolt and nut.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

  7. INSTALL MANIFOLD STAY


    1. Install the manifold stay with the bolt and nut.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

  8. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    1. A01W54NE03
      Text in Illustration
      *1 Exhaust Manifold Converter Sub-assembly
      *2 Gasket
      *3 Wooden Block

      Using a vernier caliper, measure the free length of the compression spring.

      Minimum 40.5 mm (1.59 in.)

      Tech Tips

      If the length is less than the minimum, replace the compression spring.

    2. Fully insert a new gasket to the exhaust manifold converter sub-assembly.

    3. A01VZGDE49
      Text in Illustration
      *1 Exhaust Manifold Converter Sub-assembly
      *2 Front Exhaust Pipe Assembly
      *3 Gasket
      *a Space between flanges: 8.5 mm (0.335 in.)

      Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the exhaust manifold converter sub-assembly.

      Note


      • Be sure to install the gasket in the correct direction.

      • Do not reuse the gasket.

      • Do not damage the gasket.

      • Do not push in the gasket by using the exhaust pipe when connecting it.

    4. Install a new gasket to the front exhaust pipe assembly.

    5. Connect the front exhaust pipe assembly to the exhaust pipe support.

    6. Install the front exhaust pipe assembly with the 2 compression springs, 2 bolts and 2 nuts.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

      Tech Tips

      After the installation, check that the gaps between the flanges of the exhaust manifold converter sub-assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.

      A01W5BEE01

    7. Connect the heated oxygen sensor connector.

  9. INSTALL ENGINE UNDER COVER RH

  10. INSTALL ENGINE UNDER COVER LH

  11. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH

  12. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

  13. INSPECT FOR EXHAUST GAS LEAK