OUTER REAR VIEW MIRROR INSPECTION

PROCEDURE

1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

   
   

   1. Check the operation of the mirror surface.

      
      
      1. 

         Text in Illustration

         *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

         Disconnect the outer rear view mirror assembly RH connector.

      2. Apply battery voltage and check the operation of the mirror.

         OK

         Measurement Condition Specified Condition Battery positive (+) → Terminal 1 (MV) Battery negative (-) → Terminal 10 (M+) Turns upward Battery positive (+) → Terminal 10 (M+) Battery negative (-) → Terminal 1 (MV) Turns downward Battery positive (+) → Terminal 9 (MH) Battery negative (-) → Terminal 10 (M+) Turns left Battery positive (+) → Terminal 10 (M+) Battery negative (-) → Terminal 9 (MH) Turns right

         If the result is not as specified, replace the outer rear view mirror assembly RH.

   2. Check the operation of the mirror heater.

      
      
      1. 

         Text in Illustration

         *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

         Disconnect the outer rear view mirror assembly RH connector.

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 4 (+) - 12 (-) 25°C (75°F) 7.6 to 11.4 Ω

         If the result is not as specified, replace the outer rear view mirror assembly RH.

      3. Connect a cable from the positive (+) battery terminal to terminal 2 and the negative (-) battery terminal to terminal 8, then check that the mirror becomes warm.

         Tech Tips

         It takes a short time for the mirror to become warm.

         OK
         Mirror becomes warm.

         If the result is not as specified, replace the outer rear view mirror assembly RH.

2. INSPECT OUTER MIRROR RETRACTOR RH

   
   

   1. Check the operation of the retractable mirror.

      Note

      
      

      • Disconnect and reconnect the battery between each mirror position check.

      • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

      
      
      1. 

         Text in Illustration

         *1	(A) Forward position
         *2	(B)
         *3	(C) Driving position
         *4	(D)
         *5	(E) Retracted position
         *a	Component without harness connected (Outer Mirror Retractor RH)

         Disconnect the outer mirror retractor RH connector.

      2. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

         OK

         Tester Connection Condition Specified Condition Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Forward position (A) Moves from (A) to (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Forward position (A) Does not move Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Position between forward position (A) and driving position (C) Moves from (B) to (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Position between forward position (A) and driving position (C) Moves from (B) to (A) Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Driving position (C) Moves from (C) to (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Driving position (C) Does not move Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Position between driving position (C) and retracted position (E) Moves from (D) to (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Position between driving position (C) and retracted position (E) Moves from (D) to (C) Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Retracted position (E) Does not move Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Retracted position (E) Moves from (E) to (C)

         If the result is not as specified, replace the outer mirror retractor RH.

3. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

   
   

   1. Check the operation of the mirror surface.

      
      
      1. 

         Text in Illustration

         *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

         Disconnect the outer rear view mirror assembly LH connector.

      2. Apply battery voltage and check the operation of the mirror.

         OK

         Measurement Condition Specified Condition Battery positive (+) → Terminal 1 (MV) Battery negative (-) → Terminal 10 (M+) Turns upward Battery positive (+) → Terminal 10 (M+) Battery negative (-) → Terminal 1 (MV) Turns downward Battery positive (+) → Terminal 9 (MH) Battery negative (-) → Terminal 10 (M+) Turns left Battery positive (+) → Terminal 10 (M+) Battery negative (-) → Terminal 9 (MH) Turns right

         If the result is not as specified, replace the outer rear view mirror assembly LH.

   2. Check the operation of the mirror heater.

      
      
      1. 

         Text in Illustration

         *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

         Disconnect the outer rear view mirror assembly LH connector.

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 4 (+) - 12 (-) 25°C (75°F) 7.6 to 11.4 Ω

         If the result is not as specified, replace the outer rear view mirror assembly LH.

      3. Connect a cable from the positive (+) battery terminal to terminal 2 and the negative (-) battery terminal to terminal 8, then check that the mirror becomes warm.

         Tech Tips

         It takes a short time for the mirror to become warm.

         OK
         Mirror becomes warm.

         If the result is not as specified, replace the outer rear view mirror assembly LH.

4. INSPECT OUTER MIRROR RETRACTOR LH

   
   

   1. Check the operation of the retractable mirror.

      Note

      
      

      • Disconnect and reconnect the battery between each mirror position check.

      • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

      
      
      1. 

         Text in Illustration

         *1	(A) Forward position
         *2	(B)
         *3	(C) Driving position
         *4	(D)
         *5	(E) Retracted position
         *a	Component without harness connected (Outer Mirror Retractor LH)

         Disconnect the outer mirror retractor LH connector.

      2. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

         OK

         Tester Connection Condition Specified Condition Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Forward position (A) Moves from (A) to (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Forward position (A) Does not move Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Position between forward position (A) and driving position (C) Moves from (B) to (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Position between forward position (A) and driving position (C) Moves from (B) to (A) Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Driving position (C) Moves from (C) to (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Driving position (C) Does not move Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Position between driving position (C) and retracted position (E) Moves from (D) to (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Position between driving position (C) and retracted position (E) Moves from (D) to (C) Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Retracted position (E) Does not move Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Retracted position (E) Moves from (E) to (C)

         If the result is not as specified, replace the outer mirror retractor LH.