LUGGAGE DOOR HINGE TORSION BAR INSTALLATION

CAUTION / NOTICE / HINT

Note

After installing the torsion bar, use your hand to open and close the luggage door. Make sure the luggage door can open and close smoothly.

PROCEDURE


  1. INSTALL LUGGAGE COMPARTMENT DOOR TORSION BAR SUPPORT


    1. A01W04P

      Install a new luggage compartment door torsion bar support as shown in the illustration.

  2. INSTALL LUGGAGE DOOR HINGE TORSION BAR RH


    1. Check the identification mark on the luggage door hinge torsion bar RH.

      w/o Power Trunk Lid System
      No identification marks
      w/ Power Trunk Lid System
      White
    2. A01W0P0E04
      Text in Illustration
      *a Installation Hole
      *b Installation Hole (For Adjustment)

      Set the tip of the luggage door hinge torsion bar RH in the center installation hole. The upper and lower installation holes are used for adjustment.

    3. A01W3GX

      Connect the luggage door hinge torsion bar RH to the left side of the vehicle body as shown in the illustration.

    4. A01W3W4E04

      Using SST, install the luggage door hinge torsion bar RH to the luggage door hinge and the right side of the vehicle body as shown in the illustration.

      SST
      09804-24010
    5. A01W0AU

      Connect the luggage door hinge torsion bar RH to the luggage compartment door torsion bar support as shown in the illustration.

  3. INSTALL LUGGAGE DOOR HINGE TORSION BAR LH


    1. Check the identification mark on the luggage door hinge torsion bar RH.

      w/o Power Trunk Lid System
      No identification marks
      w/ Power Trunk Lid System
      White
    2. A01W05FE04
      Text in Illustration
      *a Installation Hole
      *b Installation Hole (For Adjustment)

      Set the tip of the luggage door hinge torsion bar LH in the center installation hole. The upper and lower installation holes are used for adjustment.

    3. A01W0CK

      Connect the luggage door hinge torsion bar LH to the right side of the vehicle body as shown in the illustration.

    4. A01W237E04

      Using SST, install the luggage door hinge torsion bar LH to the luggage door hinge and the left side of the vehicle body as shown in the illustration.

      SST
      09804-24010
    5. A01W1IP

      Connect the luggage door hinge torsion bar LH to the luggage compartment door torsion bar support as shown in the illustration.

    6. A01W2U6

      Engage the 2 claws as shown in the illustration.

  4. INSTALL LUGGAGE CLOSER MOTOR ASSEMBLY (w/ Power Trunk Lid System)

    Click here

  5. INSTALL LUGGAGE COMPARTMENT DOOR HINGE COVER LH

    Click here

  6. INSTALL LUGGAGE COMPARTMENT DOOR HINGE COVER RH

    Click here

  7. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER LH


    1. Install the 3 clips.

    2. Engage the 2 fasteners and install the luggage compartment inner trim cover LH.

  8. INSTALL ROPE HOOK (for LH Side)


    1. A01W3M4

      Engage the 2 claws and install the rope hook.

  9. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)


    1. Engage the guide.

    2. Install the luggage hold belt striker assembly with the bolt.

  10. INSTALL LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY RH (w/ Power Trunk Lid System)

    Click here

  11. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER RH (w/o Power Trunk Lid System)


    1. Install the 3 clips.

    2. Engage the 2 fasteners and install the luggage compartment inner trim cover RH.

  12. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER RH (w/ Power Trunk Lid System)


    1. Install the 2 clips.

    2. Engage the 4 fasteners and install the luggage compartment inner trim cover RH.

  13. INSTALL ROPE HOOK (for RH Side)


    1. A01VZCQ

      Engage the 2 claws and install the rope hook.

  14. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)


    1. Engage the guide.

    2. Install the luggage hold belt striker assembly with the bolt.

  15. INSTALL REAR FLOOR FINISH PLATE


    1. Engage the 4 clips and install the rear floor finish plate.

    2. Install the 3 clips.

  16. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for Rear Side)


    1. Engage the 2 guides.

    2. Install the 2 luggage hold belt striker assemblies with the 2 bolts.

  17. INSTALL SPARE WHEEL COVER PAD RH


    1. Install the spare wheel cover pad RH.

  18. INSTALL SPARE WHEEL COVER PAD LH


    1. Install the spare wheel cover pad LH.

  19. INSTALL LUGGAGE COMPARTMENT FLOOR MAT


    1. Install the luggage compartment floor mat.

  20. INSTALL LUGGAGE COMPARTMENT DOOR COVER

    Click here

  21. INSTALL LUGGAGE COMPARTMENT DOOR ASSIST GRIP

    Click here

  22. INITIALIZE POWER TRUNK LID SYSTEM (w/ Power Trunk Lid System)

    Click here

  23. INSPECT POWER TRUNK LID OPERATION (w/ Power Trunk Lid System)

    Click here