POWER MIRROR CONTROL SYSTEM(w/ Reverse Shift-linked Mirror) AUTO Power Retract Mirrors do not operate

DESCRIPTION

The retractable outer mirror switch sends a voltage signal to the main body ECU (multiplex network body ECU) in accordance with switch operation (switch input signal). The main body ECU (multiplex network body ECU) uses CAN communication to send this information to the outer mirror control ECU assembly, which then controls the mirrors.

When the outer mirror control ECU assembly receives a door lock signal from the main body ECU (multiplex network body ECU) while the retractable outer mirror switch is in the AUTO position, the outer mirror control ECU assemblies operate the retract motors built into the outer rear view mirror assemblies to retract or return the outer rear view mirror assemblies.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

PROCEDURE

1. CHECK POWER RETRACT MIRROR FUNCTION

   
   

   1. Check power retract mirror function Click here.

      OK
      Power retract mirror function is normal.

   
   

   NG

   GO TO OTHER DIAGNOSIS PROCEDURE (Power Retractable Mirror do not Operate with Power Retract Mirror Switch) Click here

   OK

2. CHECK CAN COMMUNICATION SYSTEM

   
   

   1. Check for CAN communication system DTCs Click here.*1

   2. Check for CAN communication system DTCs Click here.*2

      
      

      • *1: w/o Central Gateway ECU

      • *2: w/ Central Gateway ECU

      Result
      Result Proceed to CAN DTCs are not output A CAN DTCs are output (w/o central gateway ECU) B CAN DTCs are output (w/ central gateway ECU) C

   
   

   B

   GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART) Click here

   C

   GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART) Click here

   A

3. CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

   
   

   1. Check the wireless door lock control system Click here.

      OK
      Wireless door lock control system is normal.

   
   

   NG

   GO TO WIRELESS DOOR LOCK CONTROL SYSTEM (PROBLEM SYMPTOMS TABLE) Click here

   OK

4. CHECK SMART ENTRY AND START SYSTEM (for ENTRY FUNCTION)

   
   

   1. Check the smart entry and start system (for entry function) Click here.

      OK
      Smart entry and start system (for entry function) is normal.

   
   

   NG

   GO TO SMART ENTRY AND START SYSTEM (PROBLEM SYMPTOMS TABLE) Click here

   OK

5. READ VALUE USING GTS

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the engine switch on (IG).

   3. Turn the GTS on.

   4. Enter the following menus: Body Electrical / Main Body / Data List.

   5. Read the Data List according to the display on the GTS.

      Main Body

      Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
      Auto Mirror SW	Retractable outer mirror switch signal / ON or OFF	ON: Retractable outer mirror switch in AUTO position OFF: Retractable outer mirror switch not in AUTO position	-

      OK
      On the GTS screen, ON or OFF is displayed for each item according to the table above.

   
   

   OK

   REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

   NG

6. INSPECT RETRACTABLE OUTER MIRROR SWITCH

   
   

   1. Remove the retractable outer mirror switch Click here.

   2. Inspect the retractable outer mirror switch Click here.

   
   

   NG

   REPLACE RETRACTABLE OUTER MIRROR SWITCH Click here

   OK

7. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - RETRACTABLE OUTER MIRROR SWITCH)

   
   

   1. Disconnect the H10 main body ECU (multiplex network body ECU) connector.

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition H72-3 (MAT) - H10-27 (RTR) Always Below 1 Ω H72-3 (MAT) - Body ground Always 10 kΩ or higher

   
   

   OK

   REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU - RETRACTABLE OUTER MIRROR SWITCH)