ROOF HEADLINING REASSEMBLY

PROCEDURE


  1. INSTALL NO. 1 ROOF WIRE


    1. When using a new roof headlining:


      1. Immediately before installing the No. 1 roof wire, cut off the portion shown in the illustration.

        Figure 1. for LHD:

        B001OJTC01
        *A for Standard *B for Glass Roof
        *C w/o Pre-crash Safety System without Rain Sensor *D w/o Pre-crash Safety System with Rain Sensor
        *E w/ Pre-crash Safety System *F w/ Forward Recognition with Heater Hood Sub-assembly
        *a Cut Off Size - -
        Cut Off Size
        Area Dimension
        A 10 mm (0.394 in.)

        Figure 2. for RHD:

        B001OGCC01
        *A for Standard *B for Glass Roof
        *C w/o Pre-crash Safety System without Rain Sensor *D w/o Pre-crash Safety System with Rain Sensor
        *E w/ Pre-crash Safety System *F w/ Forward Recognition with Heater Hood Sub-assembly
        *a Cut Off Size - -
        Cut Off Size
        Area Dimension
        A 10 mm (0.394 in.)

    2. Apply double-sided tape as shown in the illustration.

      B001NN2E01
      Text in Illustration
      *A for Standard *B for Glass Roof
      *a Double-sided Tape Size *b Tape Attachment Locations (Reference)
      *c Marking - -
      B001OGU Double-sided Tape - -
      Double-sided Tape Size
      Area Dimension
      A 1 mm (0.0394 in.)
      B 10 mm (0.394 in.)

    3. Peel off the release paper from the double-sided tape.

    4. Attach the No. 1 roof wire along the double-sided tape so that the marking surface of the wire harness faces downward.

    5. Align the edge of the marking tape (A) on the No. 1 roof wire with the markings on the roof headlining.

      B001OJAE03
      Text in Illustration
      *A for Standard *B for Glass Roof
      *a Marking Tape (A) *b Marking
      *c Marking Tape (B) *d Clamp (A)
      *e Marking Tape (C) *f Adjustment Area
      *g Clamp (B) *h Marking Tape (D)
      *i Marking Tape (E) - -

    6. Align the marking tape (B) on the No. 1 roof wire with the vehicle front end of the roof headlining.

    7. Attach the No. 1 roof wire, starting from the marking tape (B) to the marking tape (A) while aligning it with the double-sided tape.

      Note


      • Securely attach the No. 1 roof wire.

      • If any portion of the No. 1 roof wire is left loose, this will cause abnormal noise. Make sure to attach the No. 1 roof wire without leaving any of it loose.

    8. Turn the visor assembly LH connector clockwise approximately 90° to install it to the roof headlining.

    9. Engage the clamp (A).

    10. Align the edge of the marking tape (C) on the No. 1 roof wire with the markings on the roof headlining.

    11. Attach the No. 1 roof wire, starting from the marking tape (C) to the marking tape (B) while aligning it with the double-sided tape.

      Note


      • Securely attach the No. 1 roof wire.

      • If any portion of the No. 1 roof wire is left loose, this will cause abnormal noise. Make sure to attach the No. 1 roof wire without leaving any of it loose.

      Tech Tips

      Secure the extra length of the No. 1 roof wire in the adjustment area using double-sided tape.

    12. Engage the 3 clamps (B).

    13. Align the edge of the marking tape (D) on the No. 1 roof wire with the markings on the roof headlining.

    14. Align the edge of the marking tape (E) on the No. 1 roof wire with the markings on the roof headlining.

    15. Attach the No. 1 roof wire, starting from the marking tape (D) to the marking tape (E) while aligning it with the double-sided tape.

      Note


      • Securely attach the No. 1 roof wire.

      • If any portion of the No. 1 roof wire is left loose, this will cause abnormal noise. Make sure to attach the No. 1 roof wire without leaving any of it loose.

    16. Turn the visor assembly RH connector clockwise approximately 90° to install it to the roof headlining.

    17. Apply adhesive tape to the roof headlining as shown in the illustration.

      B001OE5E03
      Text in Illustration
      *A for Standard *B for Glass Roof
      *1 No. 1 Roof Wire - -
      *a Adhesive Tape Size *b Correct
      *c Incorrect - -
      B001OGU Adhesive Tape - -
      Adhesive Tape Size
      Area Dimension
      A 20 mm (0.787 in.)
      B 100 mm (3.94 in.)

  2. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

    Click here

  3. INSTALL VANITY LIGHT ASSEMBLY


    1. Install the vanity light assembly Click here.

      Tech Tips

      Use the same procedure for the other vanity light.