MULTI-MODE MANUAL TRANSAXLE SYSTEM Engine does not Start

DTC Code DTC Name
Engine does not Start

DESCRIPTION

If any malfunctions are suspected in the transaxle control system after reassembling or repairing transaxle system components, perform troubleshooting in accordance with the following chart.

PROCEDURE

  1. CHECK DTC OUTPUT

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Multi-Mode M/T / Trouble Codes.

      Powertrain > Multi-Mode M/T > Trouble Codes

    5. Read the DTCs using the GTS.

      Result

      Result

      Proceed to

      DTCs are not output

      A

      DTCs are output

      B
    B

    GO TO DTC CHART

    Click hereClick here

    A

  2. READ VALUE USING GTS (LEARN-CLUTCH STOP POINT)

    1. Enter the following menus: Powertrain / Multi-Mode M/T / Data List / Learn-Clutch Stop Point.

    2. Read the Data List according to the display on the GTS.

      Powertrain > Multi-Mode M/T > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      Learn-Clutch Stop Point

      Clutch actuator stopper position learning

      Notexec, Fail or Exec

      Exec: Initialization and learning complete

      -

      Powertrain > Multi-Mode M/T > Data List

      Tester Display

      Learn-Clutch Stop Point

    Result

    Result

    Proceed to

    Executed (Exec)

    A

    Not executed (Notexec)

    B

    Failure (Fail)

    C
    B

    PERFORM INITIALIZATION

    Click here

    C

    CHECK CLUTCH SYSTEM (GO TO EFFECT OF MULTI-MODE M/T PART MALFUNCTION ON LEARNING)

    Click here

    A

  3. READ VALUE USING GTS (LEARNING-T/M)

    1. Enter the following menus: Powertrain / Multi-Mode M/T / Data List / Learning-T/M.

    2. Read the Data List according to the display on the GTS.

      Powertrain > Multi-Mode M/T > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      Learning-T/M

      Learning T/M system

      Notexec, Fail or Exec

      Exec: Initialization and learning complete

      -

      Powertrain > Multi-Mode M/T > Data List

      Tester Display

      Learning-T/M

    Result

    Result

    Proceed to

    Executed (Exec)

    A

    Not executed (Notexec)

    B

    Failure (Fail)

    C
    B

    PERFORM INITIALIZATION

    Click here

    C

    CLEAR LEARNING VALUE AND EXECUTE LEARNING AGAIN (GO TO EFFECT OF MULTI-MODE M/T PART MALFUNCTION ON LEARNING)

    Click here

    A

  4. READ VALUE USING GTS (GEAR POSITION (CURRENT))

    1. Enter the following menus: Powertrain / Multi-Mode M/T / Data List / Gear Position (Current).

      Powertrain > Multi-Mode M/T

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      Gear Position (Current)

      Current gear position

      1st, 2nd, 3rd, 4th, 5th, N, R

      Actual gear position displayed

      -

      Powertrain > Multi-Mode M/T > Data List

      Tester Display

      Gear Position (Current)

    2. Move the shift lever to N (neutral).

    3. In accordance with the display on the GTS, read the Data List.

      Result

      Result

      Proceed to

      Neutral (N)

      A

      Other than neutral (N)

      B
    B

    CHECK TRANSAXLE ASSEMBLY (GO TO EFFECT OF MULTI-MODE M/T PART MALFUNCTION ON LEARNING)

    Click here

    A

  5. INSPECT NEUTRAL POSITION SWITCH

    1. Inspect the neutral position switch.

      Click here

    Result

    Proceed to

    OK

    NG
    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

    Click here

    NG

    REPLACE NEUTRAL POSITION SWITCH

    Click here