OUTER REAR VIEW MIRROR INSPECTION

PROCEDURE

1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

   1. Check the operation of the mirror surface.

      1. 

         *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

         Disconnect the outer rear view mirror assembly LH connector.

      2. Apply battery voltage and check the operation of the mirror.

         OK

         Measurement Condition	Specified Condition
         Battery positive (+) → Terminal 6 (MV) Battery negative (-) → Terminal 5 (M+)	Turns upward
         Battery positive (+) → Terminal 5 (M+) Battery negative (-) → Terminal 6 (MV)	Turns downward
         Battery positive (+) → Terminal 4 (MH) Battery negative (-) → Terminal 5 (M+)	Turns left
         Battery positive (+) → Terminal 5 (M+) Battery negative (-) → Terminal 4 (MH)	Turns right

         If the result is not as specified, replace the outer mirror retractor LH.

   2. Check the operation of the retractable mirror.

      Note:

      • Disconnect and reconnect the battery between each mirror position check.

      • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

      1. 

         *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

         Disconnect the outer rear view mirror assembly LH connector.

      2. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

         OK

         Measurement Condition	Mirror Position	Specified Condition
         Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 9 (MF)	Forward position A	Moves from A to retracted position E
         Battery positive (+) → Terminal 9 (MF) Battery negative (-) → Terminal 3 (MR)	Forward position A	Does not move
         Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 9 (MF)	Position between forward position A and driving position C	Moves from B to retracted position E
         Battery positive (+) → Terminal 9 (MF) Battery negative (-) → Terminal 3 (MR)	Position between forward position A and driving position C	Moves from B to forward position A
         Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 9 (MF)	Driving position C	Moves from C to retracted position E
         Battery positive (+) → Terminal 9 (MF) Battery negative (-) → Terminal 3 (MR)	Driving position C	Does not move
         Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 9 (MF)	Position between driving position C and retracted position E	Moves from D to retracted position E
         Battery positive (+) → Terminal 9 (MF) Battery negative (-) → Terminal 3 (MR)	Position between driving position C and retracted position E	Moves from D to driving position C
         Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 9 (MF)	Retracted position E	Does not move
         Battery positive (+) → Terminal 9 (MF) Battery negative (-) → Terminal 3 (MR)	Retracted position E	Moves from E to driving position C

         If the result is not as specified, replace the outer mirror retractor LH.

   3. Check the operation of the mirror heater.

      1. 

         *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

         Disconnect the outer rear view mirror assembly LH connector.

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection	Condition	Specified Condition
         2 (+) - 8 (-)	25°C (75°F)	5.4 to 8.1 Ω

         If the result is not as specified, check the outer rear view mirror sub-assembly LH (Click here).

         If the result is not as specified, replace the outer mirror retractor LH.

      3. Connect the cable from the positive (+) battery terminal to terminal 2 and the negative (-) battery terminal to terminal 8, and then check that the mirror becomes warm.

         Tip:

         It takes a short time for the mirror to become warm.

         OK

         Mirror becomes warm.

         If the result is not as specified, check the outer rear view mirror sub-assembly LH (Click here).

         If the result is not as specified, replace the outer mirror retractor LH.

   4. 

      *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

      Check the side turn signal light assembly LH.

      1. Apply battery voltage to the terminals of the connector, and check the illumination condition.

         OK

         If the result is not as specified, replace the side turn signal light assembly LH.

         Measurement Connection	Specified Condition
         Battery positive (+) → Terminal 10 (B) Battery negative (-) → Terminal 11 (E)	Side turn light illuminates

         If the result is not as specified, check the side turn signal light assembly LH (Click here).

         If the result is not as specified, replace the outer mirror retractor LH.

2. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

   1. Check the operation of the mirror surface.

      1. 

         *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

         Disconnect the outer rear view mirror assembly RH connector.

      2. Apply battery voltage and check the operation of the mirror.

         OK

         Measurement Condition	Specified Condition
         Battery positive (+) → Terminal 6 (MV) Battery negative (-) → Terminal 5 (M+)	Turns upward
         Battery positive (+) → Terminal 5 (M+) Battery negative (-) → Terminal 6 (MV)	Turns downward
         Battery positive (+) → Terminal 4 (MH) Battery negative (-) → Terminal 5 (M+)	Turns left
         Battery positive (+) → Terminal 5 (M+) Battery negative (-) → Terminal 4 (MH)	Turns right

         If the result is not as specified, replace the outer mirror retractor RH.

   2. Check the operation of the retractable mirror.

      Note:

      • Disconnect and reconnect the battery between each mirror position check.

      • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

      1. 

         *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

         Disconnect the outer rear view mirror assembly RH connector.

      2. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

         OK

         Measurement Condition	Mirror Position	Specified Condition
         Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 9 (MF)	Forward position A	Moves from A to retracted position E
         Battery positive (+) → Terminal 9 (MF) Battery negative (-) → Terminal 3 (MR)	Forward position A	Does not move
         Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 9 (MF)	Position between forward position A and driving position C	Moves from B to retracted position E
         Battery positive (+) → Terminal 9 (MF) Battery negative (-) → Terminal 3 (MR)	Position between forward position A and driving position C	Moves from B to forward position A
         Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 9 (MF)	Driving position C	Moves from C to retracted position E
         Battery positive (+) → Terminal 9 (MF) Battery negative (-) → Terminal 3 (MR)	Driving position C	Does not move
         Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 9 (MF)	Position between driving position C and retracted position E	Moves from D to retracted position E
         Battery positive (+) → Terminal 9 (MF) Battery negative (-) → Terminal 3 (MR)	Position between driving position C and retracted position E	Moves from D to driving position C
         Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 9 (MF)	Retracted position E	Does not move
         Battery positive (+) → Terminal 9 (MF) Battery negative (-) → Terminal 3 (MR)	Retracted position E	Moves from E to driving position C

         If the result is not as specified, replace the outer mirror retractor RH.

   3. Check the operation of the mirror heater.

      1. 

         *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

         Disconnect the outer rear view mirror assembly RH connector.

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection	Condition	Specified Condition
         2 (+) - 8 (-)	25°C (75°F)	5.4 to 8.1 Ω

         If the result is not as specified, check the outer rear view mirror sub-assembly RH (Click here)

         If the result is not as specified, replace the outer mirror retractor RH.

      3. Connect the cable from the positive (+) battery terminal to terminal 2 and the negative (-) battery terminal to terminal 8, and then check that the mirror becomes warm.

         Tip:

         It takes a short time for the mirror to become warm.

         OK

         Mirror becomes warm.

         If the result is not as specified, check the outer rear view mirror sub-assembly RH (Click here).

         If the result is not as specified, replace the outer mirror retractor RH.

   4. 

      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

      Check the side turn signal light assembly RH.

      1. Apply battery voltage to the terminals of the connector, and check the illumination condition.

         OK

         Measurement Connection	Specified Condition
         Battery positive (+) → Terminal 10 (B) Battery negative (-) → Terminal 11 (E)	Side turn light illuminates

         If the result is not as specified, check the side turn signal light assembly RH (Click here).

         If the result is not as specified, replace the outer mirror retractor RH.