ECD SYSTEM (w/ DPF), Diagnostic DTC:P115D, P115E

DTC Code DTC Name
P115D Intake Manifold Runner Control Circuit Low (Bank 2)
P115E Intake Manifold Runner Control Circuit High (Bank 2)

DESCRIPTION

Refer to DTC P2006 Click here.

P115D
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
2 seconds after engine is started, race engine for 1 second Open in vacuum switching valve (for No. 2 swirl control valve) circuit for 0.5 seconds (2 trip detection logic).

  • Vacuum switching valve (for No. 2 swirl control valve)

  • Open in vacuum switching valve (for No. 2 swirl control valve) circuit

  • ECM
P115E
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
2 seconds after engine is started, race engine for 1 second Short in vacuum switching valve (for No. 2 swirl control valve) circuit for 0.5 seconds (2 trip detection logic).

  • Vacuum switching valve (for No. 2 swirl control valve)

  • Short in vacuum switching valve (for No. 2 swirl control valve) circuit

  • ECM

WIRING DIAGRAM

B007WE4E07

INSPECTION PROCEDURE

Note


  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.

  • After replacing the ECM, the new ECM needs registration Click here and initialization Click here.

  • After replacing the fuel supply pump assembly, the ECM needs initialization Click here.

  • After replacing an injector assembly, the ECM needs registration Click here.

Tech Tips

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. INSPECT VACUUM SWITCHING VALVE FOR NO. 2 SWIRL CONTROL VALVE (RESISTANCE)


    1. Inspect the vacuum switching valve (for No. 2 swirl control valve) Click here.


    NG

    REPLACE VACUUM SWITCHING VALVE (FOR NO. 2 SWIRL CONTROL VALVE) Click here

    OK

  2. INSPECT VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) (POWER SOURCE VOLTAGE)


    1. B007VX6E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Vacuum Switching Valve (for No. 2 Swirl Control Valve))

      Disconnect the vacuum switching valve (for No. 2 swirl control valve) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      D91-2 - Body ground Ignition switch ON 11 to 14 V

    NG

    CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR NO. 2 SWIRL CONTROL VALVE) - NO. 1 INTEGRATION RELAY) Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) - ECM)


    1. Disconnect the vacuum switching valve (for No. 2 swirl control valve) connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D91-1 - D99-107 (SCV2) Always Below 1 Ω
      D91-1 or D99-107 (SCV2) - Body ground Always 10 kΩ or higher

    4. Reconnect the vacuum switching valve (for No. 2 swirl control valve) connector.

    5. Reconnect the ECM connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  4. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  5. CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR NO. 2 SWIRL CONTROL VALVE) - NO. 1 INTEGRATION RELAY)


    1. Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly.

    2. Disconnect the vacuum switching valve (for No. 2 swirl control valve) connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard Resistance
      Tester Connection Condition Specified Condition
      10B-4 - D91-2 Always Below 1 Ω
      10B-4 or D91-2 - Body ground Always 10 kΩ or higher

    4. Reinstall the No. 1 integration relay.

    5. Reconnect the vacuum switching valve (for No. 2 swirl control valve) connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  6. CHECK ECM POWER SOURCE CIRCUIT


    1. Check the ECM power source circuit Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  7. REPLACE VACUUM SWITCHING VALVE (FOR NO. 2 SWIRL CONTROL VALVE)


    1. Replace the vacuum switching valve (for No. 2 swirl control valve).


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  8. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace harness or connector.


    NEXT

  9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Clear the DTCs Click here.

    3. Start the engine and wait for 3 seconds or more.

    4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    5. Confirm that the DTC is not output again.


    NEXT

    END