NAVIGATION SYSTEM Illumination Circuit

DTC Code DTC Name
Illumination Circuit

DESCRIPTION

Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

Figure 1. for Sedan
E229630E29
Figure 2. for Hatchback, Wagon
E319115E09

CAUTION / NOTICE / HINT

Note:

  • The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE

  1. CHECK ILLUMINATION

    1. Check if the illumination for the radio and display receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

      Result

      Result

      Proceed to

      Illumination comes on for all components except steering pad switch assembly.

      A

      Illumination comes on for all components except radio and display receiver assembly.

      B

      No illumination comes on (radio and display receiver assembly, hazard switch, heater control switch, etc.).

      C
    B

    CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)Click here

    C

    GO TO LIGHTING SYSTEM

    Click here

    A

  2. CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

    1. Disconnect the E6 spiral cable with sensor sub-assembly connector (w/ VSC).

      Disconnect the E6 spiral cable sub-assembly connector (w/o VSC).

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      E6-13 (IL+2) - Body ground

      Light control switch in the tail or head position

      11 to 14 V

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT STEERING PAD SWITCH ASSEMBLY

    1. Remove the steering pad switch assembly.

      Click here

    2. Connect a positive (+) lead from the battery to terminal 5 (IL+2) and a negative (-) lead to terminal 3 (-DP) of the steering pad switch assembly connector.(for Sedan)

      E265406C01

      *a

      Component without harness connected

      (Steering Pad Switch Assembly)

      -

      -

    3. Connect a positive (+) lead from the battery to terminal 5 (IL+2) and a negative (-) lead to terminal 8 (EAU) of the steering pad switch assembly connector.(for Hatchback, Wagon)

      E317423C01

      *a

      Component without harness connected

      (Steering Pad Switch Assembly)

      -

      -

    4. Check if the illumination for the steering pad switch assembly comes on.

      OK

      Illumination for the steering pad switch assembly comes on.

    Result

    Result

    Proceed to

    OK (w/ VSC)

    A

    OK (w/o VSC)

    B

    NG

    C
    B

    INSPECT SPIRAL CABLE SUB-ASSEMBLYClick here

    C

    REPLACE STEERING PAD SWITCH ASSEMBLY

    Click here

    A

  4. INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    1. Remove the spiral cable with sensor sub-assembly.

      Click here

    2. Figure 4. for Hatchback, Wagon
      E263757C38

      *a

      Component without harness connected

      (Spiral Cable with Sensor Sub-assembly)

      *b

      Steering pad switch assembly side

      *c

      Vehicle side
      Figure 3. for Sedan
      E263757C08

      *a

      Component without harness connected

      (Spiral Cable with Sensor Sub-assembly)

      *b

      Steering Pad Switch Assembly Side

      *c

      Vehicle Side

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Table 1. for Sedan

      Tester Connection

      Condition

      Specified Condition

      z1-5 (IL+2) - E6-13 (IL+2)

      Center

      3 Ω or less

      2.5 rotations to the left

      2.5 rotations to the right

      z1-3 (-DP) - E6-11 (-DP)

      Center

      3 Ω or less

      2.5 rotations to the left

      2.5 rotations to the right
      Table 2. for Hatchback, Wagon

      Tester Connection

      Condition

      Specified Condition

      z1-5 (IL+2) - E6-13 (IL+2)

      Center

      3 Ω or less

      2.5 rotations to the left

      2.5 rotations to the right

      z1-8 (EAU) - E6-3 (EAU)

      Center

      3 Ω or less

      2.5 rotations to the left

      2.5 rotations to the right

    3. After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance according to the table below.

      Standard Resistance

      Table 3. for Sedan

      Tester Connection

      Condition

      Specified Condition

      z1-5 (IL+2) - E6-13 (IL+2)

      Always

      3 Ω or less

      z1-3 (-DP) - E6-11 (-DP)

      Always

      3 Ω or less
      Table 4. for Hatchback, Wagon

      Tester Connection

      Condition

      Specified Condition

      z1-5 (IL+2) - E6-13 (IL+2)

      Always

      3 Ω or less

      z1-8 (EAU) - E6-3 (EAU)

      Always

      3 Ω or less
      Note:

      • Press and hold the lock located in the center of the spiral cable with sensor sub-assembly to rotate the spiral cable with sensor sub-assembly.

      • The spiral cable with sensor sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable with sensor sub-assembly may prevent the airbag from deploying.

      • As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.

    Result

    Proceed to

    OK

    NG
    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - BODY GROUND)

    NG

    REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Click here

  5. INSPECT SPIRAL CABLE SUB-ASSEMBLY

    1. Remove the spiral cable sub-assembly.

      Click here

    2. E263757C08

      *a

      Component without harness connected

      (Spiral Cable Sub-assembly)

      *b

      Steering Pad Switch Assembly Side

      *c

      Vehicle Side

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      z1-5 (IL+2) - E6-13 (IL+2)

      Center

      3 Ω or less

      2.5 rotations to the left

      2.5 rotations to the right

      z1-3 (-DP) - E6-11 (-DP)

      Center

      3 Ω or less

      2.5 rotations to the left

      2.5 rotations to the right

    3. After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      z1-5 (IL+2) - E6-13 (IL+2)

      Always

      3 Ω or less

      z1-3 (-DP) - E6-11 (-DP)

      Always

      3 Ω or less
      Note:

      • Press and hold the lock located in the center of the spiral cable sub-assembly to rotate the spiral cable sub-assembly.

      • The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying.

      • As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.

    Result

    Proceed to

    OK

    NG
    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

    NG

    REPLACE SPIRAL CABLE SUB-ASSEMBLY

    Click here

  6. CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

    1. Disconnect the E1 radio and display receiver assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      E1-10 (ILL+) - Body ground

      Light control switch in the tail or head position

      11 to 14 V

    Result

    Proceed to

    OK

    NG
    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

    Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR