SEAT BELT WARNING SYSTEM(w/o Occupant Classification System) Rear Seat Belt Warning Light Malfunction

DTC Code DTC Name
Rear Seat Belt Warning Light Malfunction

DESCRIPTION

When a rear door is opened and closed (the rear door courtesy light switch turns on and off) with the ignition switch ON, or when a rear door is opened and closed (the rear door courtesy light switch turns on and off) and then the ignition switch is turned to ON, the rear seat belt warning light in the combination meter assembly turns on to inform the driver of condition of the rear seat belts. If a rear seat belt is fastened or unfastened, the warning light changes to indicate the current condition of the rear seat belts.

Only for vehicles with a rear seat belt indicator.

WIRING DIAGRAM

C279309E01

CAUTION / NOTICE / HINT

Note:

PROCEDURE

  1. READ VALUE USING GTS (RL DOOR COURTESY SW, RR DOOR COURTESY SW)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.

      Body Electrical > Main Body > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      RR Door Courtesy SW

      Rear door LH courtesy light switch signal

      ON/OFF

      ON: Rear door LH open

      OFF: Rear door LH closed

      -

      RL Door Courtesy SW

      Rear door RH courtesy light switch signal

      ON/OFF

      ON: Rear door RH open

      OFF: Rear door RH closed

      -

      Body Electrical > Main Body > Data List

      Tester Display

      RR Door Courtesy SW

      RL Door Courtesy SW

    Result

    Result

    Proceed to

    ON or OFF is displayed on the GTS screen according to the rear door courtesy light switch condition

    A

    ON or OFF is not displayed normally on the GTS screen according to the rear door courtesy light switch condition

    B
    B

    GO TO LIGHTING SYSTEM

    Click hereClick here

    A

  2. READ VALUE USING GTS (2ND-ROW SEATBELT BUCKLE [R], 2ND-ROW SEATBELT BUCKLE [L], 2ND-ROW SEATBELT BUCKLE [C])

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Combination Meter / Data List.

    5. Read the Data List according to the display on the GTS.

      Body Electrical > Combination Meter > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      2nd-Row Seatbelt Buckle (R)

      Rear seat belt buckle RH signal

      ON/OFF

      ON: Rear seat belt RH fastened

      OFF: Rear seat belt RH unfastened

      -

      2nd-Row Seatbelt Buckle (L)

      Rear seat belt buckle LH signal

      ON/OFF

      ON: Rear seat belt LH fastened

      OFF: Rear seat belt LH unfastened

      -

      2nd-Row Seatbelt Buckle (C)

      Rear seat center belt buckle signal

      ON/OFF

      ON: Rear seat center belt fastened

      OFF: Rear seat center belt unfastened

      -

      Body Electrical > Combination Meter > Data List

      Tester Display

      2nd-Row Seatbelt Buckle (R)

      2nd-Row Seatbelt Buckle (L)

      2nd-Row Seatbelt Buckle (C)

    Result

    Result

    Proceed to

    ON or OFF is displayed on the GTS screen according to the rear seat belt condition

    A

    ON or OFF is not displayed normally on the GTS screen according to the rear seat belt condition

    B
    B

    INSPECT REAR SEAT INNER BELT ASSEMBLYClick here

    A

  3. PERFORM ACTIVE TEST USING GTS (REAR SEAT BELT)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Combination Meter / Data List.

    5. Read the Data List according to the display on the GTS.

      Body Electrical > Combination Meter > Active Test

      Tester Display

      Measurement Item

      Control Range

      Diagnostic Note

      Rear Seat Belt

      Rear seat belt warning light

      ON/OFF

      Confirm that the vehicle is stopped and the engine is idling.

      Body Electrical > Combination Meter > Active Test

      Tester Display

      Rear Seat Belt

      OK

      The rear seat belt warning light on the combination meter assembly operates normally.

    Result

    Proceed to

    OK

    NG
    NG

    INSPECT TELLTALE LIGHT ASSEMBLYClick here

    OK

  4. REPLACE COMBINATION METER ASSEMBLY

    1. Replace the combination meter assembly with a new one.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  5. CHECK REAR SEAT BELT WARNING LIGHT

    1. Check the operation of the rear seat belt warning light.

      Click here

    Result

    Proceed to

    The rear seat belt warning light operates normally.

    The rear seat belt warning light operates abnormally.
    The rear seat belt warning light operates normally.

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    Click here(for LHD)

    Click here(for RHD)

    The rear seat belt warning light operates abnormally.

    END (COMBINATION METER ASSEMBLY WAS DEFECTIVE)

    Click here

  6. INSPECT TELLTALE LIGHT ASSEMBLY

    1. Remove the telltale light assembly.

      Click here

    2. Inspect the telltale light assembly.

      Click here

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE TELLTALE LIGHT ASSEMBLY

    Click here

    OK

  7. CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)

    1. Disconnect the G43 telltale light assembly connector.

    2. Disconnect the G16 combination meter assembly meter connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      G43-22 (RLID) - G16-1 (RLMT)

      Always

      Below 1 Ω

      G43-23 (RCID) - G16-2 (RCMT)

      G43-24 (RRID) - G16-3 (RRMT)

      G43-22 (RLID) - Body ground

      Always

      10 kΩ or higher

      G43-23 (RCID) - Body ground

      G43-24 (RRID) - Body ground

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE COMBINATION METER ASSEMBLY

    Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  8. INSPECT REAR SEAT INNER BELT ASSEMBLY

    1. for LH, RH:

      Remove the rear seat inner belt assembly.

      Click here

    2. for Center:

      Remove the rear center lap type seat belt assembly RH.

      Click here

    3. for LH, RH:

      Inspect the rear seat inner belt assembly.

      Click here

    4. for Center:

      Inspect the rear center lap type seat belt assembly RH.

      Click here

    Result

    Proceed to

    OK

    NG (for LH)

    NG (for Center)

    NG (for RH)
    NG (for LH)

    REPLACE REAR SEAT INNER BELT ASSEMBLY LH

    Click here

    NG (for Center)

    REPLACE REAR CENTER LAP TYPE SEAT BELT ASSEMBLY RH

    Click here

    NG (for RH)

    REPLACE REAR SEAT INNER BELT ASSEMBLY RH

    Click here

    OK

  9. CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)

    1. Disconnect the M12*1, M13*2 or M14*3 rear seat inner belt assembly connector.

      • *1: for RH

        *2: for Center

        *3: for LH

    2. Disconnect the G16 combination meter assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      for LH

      Tester Connection

      Condition

      Specified Condition

      M14-1 - G16-24 (RLSB)

      Always

      Below 1 Ω

      M14-2 - Body ground

      M14-1 - Body ground

      Always

      10 kΩ or higher

      for Center

      Tester Connection

      Condition

      Specified Condition

      M13-1 - G16-25 (RCSB)

      Always

      Below 1 Ω

      M13-2 - Body ground

      M13-1 - Body ground

      Always

      10 kΩ or higher

      for RH

      Tester Connection

      Condition

      Specified Condition

      M12-1 - G16-26 (RRSB)

      Always

      Below 1 Ω

      M12-2 - Body ground

      M12-1 - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE COMBINATION METER ASSEMBLY

    Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR