ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
*A |
for Hatchback, Wagon |
*B |
for Sedan |
*C |
for Half Cover Type |
*D |
for Metal Type |
*1 |
CENTER NO. 4 ENGINE UNDER COVER |
*2 |
FRONT LOWER BUMPER ABSORBER |
*3 |
NO. 1 ENGINE UNDER COVER |
*4 |
REAR ENGINE UNDER COVER LH |
*5 |
REAR ENGINE UNDER COVER RH |
- |
- |
ILLUSTRATION
*1 |
AIR CLEANER CAP SUB-ASSEMBLY |
*2 |
AIR CLEANER CASE SUB-ASSEMBLY |
*3 |
BATTERY |
*4 |
NO. 1 ENGINE COVER |
*5 |
NO. 1 RADIATOR HOSE |
*6 |
PURGE VALVE (PURGE VSV) |
*7 |
AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
*8 |
BATTERY CLAMP SUB-ASSEMBLY |
*9 |
BATTERY CLAMP BOLT |
*10 |
BATTERY TRAY |
*11 |
RADIATOR PIPE |
- |
- |
 |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
*A |
for LHD |
*B |
for RHD |
*1 |
CHECK VALVE TO BRAKE BOOSTER HOSE |
*2 |
FUEL TUBE SUB-ASSEMBLY |
*3 |
HEATER WATER INLET HOSE A |
*4 |
ENGINE WIRE |
*5 |
NO. 2 RADIATOR HOSE |
*6 |
HEATER WATER OUTLET HOSE A |
*7 |
UNION TO CONNECTOR TUBE HOSE |
*8 |
NO. 2 FUEL PIPE CLAMP |
*9 |
FUEL DELIVERY PIPE |
*10 |
NO. 1 RELAY BLOCK COVER |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
*A |
w/ Air Conditioning System |
- |
- |
*1 |
COLUMN HOLE COVER SILENCER SHEET |
*2 |
DISCHARGE HOSE SUB-ASSEMBLY |
*3 |
FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) |
*4 |
GENERATOR ASSEMBLY |
*5 |
NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY |
*6 |
SUCTION HOSE SUB-ASSEMBLY |
*7 |
V-RIBBED BELT |
*8 |
O-RING |
*9 |
GASKET |
*10 |
COMPRESSION SPRING |
*11 |
TERMINAL CAP |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
 |
Compressor oil ND-OIL 8 or equivalent |
- |
- |
ILLUSTRATION
*A |
Type A |
*B |
Type B |
*C |
w/ Reinforcement |
- |
- |
*1 |
FRONT ENGINE MOUNTING INSULATOR |
*2 |
FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT |
*3 |
FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
*4 |
FRONT SUSPENSION MEMBER REAR BRACE LH |
*5 |
FRONT SUSPENSION MEMBER REAR BRACE RH |
*6 |
FRONT SUSPENSION MEMBER REINFORCEMENT LH |
*7 |
FRONT SUSPENSION MEMBER REINFORCEMENT RH |
*8 |
NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
*9 |
REAR ENGINE MOUNTING INSULATOR |
*10 |
TRANSMISSION CONTROL CABLE ASSEMBLY |
*11 |
FRONT CROSS MEMBER SUB-ASSEMBLY |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
 |
Do not apply lubricants |
ILLUSTRATION
*A |
Type A |
*B |
Type B |
*C |
w/ Air Conditioning System |
- |
- |
*1 |
COMPRESSOR ASSEMBLY WITH PULLEY |
*2 |
ENGINE MOUNTING INSULATOR LH |
*3 |
ENGINE MOUNTING INSULATOR RH |
*4 |
ENGINE WIRE |
*5 |
COOLER PIPE CLAMP BRACKET |
*6 |
COOLER PIPE CLAMP |
*7 |
RADIATOR RESERVOIR TANK |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
*1 |
CLUTCH DISC ASSEMBLY |
*2 |
FLYWHEEL HOUSING SIDE COVER |
*3 |
FLYWHEEL SUB-ASSEMBLY |
*4 |
MANUAL TRANSAXLE ASSEMBLY |
*5 |
NO. 1 CLUTCH HOSE |
*6 |
STARTER ASSEMBLY |
*7 |
TRANSMISSION CONTROL CABLE ASSEMBLY |
*8 |
CLUTCH COVER ASSEMBLY |
*9 |
NO. 3 ENGINE WIRE |
*10 |
WIRE HARNESS |
*11 |
ENGINE ASSEMBLY |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
★ |
Precoated part |
- |
- |
ILLUSTRATION
*1 |
BLEEDER CLUTCH RELEASE TUBE |
*2 |
CLUTCH RELEASE BLEEDER SUB-ASSEMBLY |
*3 |
CLUTCH RELEASE CYLINDER TO BLEEDER TUBE |
*4 |
CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY |
*5 |
MANUAL TRANSAXLE ASSEMBLY |
*6 |
CLUTCH TUBE BOOT |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
Clutch spline grease |
- |
- |