POWER SLIDE DOOR SYSTEM Power Slide Door LH does not Operate When Satellite Switch is Pressed

DESCRIPTION

The door control relay assembly controls the power slide door and activates the slide motor assembly.

Tech Tips

Before using this flowchart, perform the self-diagnostic mode inspection Click here and make sure no code is output.

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK BASIC FUNCTIONS


    1. When the engine is running, (1) to (5) are required for the power slide door to operate.


      1. The battery voltage is 11 V or more.

      2. The vehicle's speed is less than 3 km/h (1 mph) and the shift lever is moved to the P position.

      3. The power slide door main switch is turned ON (the button is not pushed).

      4. The slide door is unlocked (the position switch is ON).

      5. An open circuit in the power slide door sensor assembly is not detected.

    2. When the engine is not running, (1) to (4) are required for the power slide door to operate.


      1. The battery voltage is 11 V or more.

      2. The power slide door main switch is turned ON (the button is not pushed).

      3. The slide door is unlocked (the position switch is ON).

      4. An open circuit in the power slide door sensor assembly is not detected.

        Tech Tips


        • For the inside handle, the power slide door can operate only when the child lock is OFF.

        • For the outside handle, the power slide door can operate even when the child lock is ON.

    3. Check that the power slide door malfunctions.

      Result
      Result Proceed to
      Nothing operates or moves A
      Motor is emitting sounds but slide door does not move (lock is released but door does not open) B

    B

    INSPECT SLIDE DOOR MOTOR ASSEMBLY Click here

    A

  2. CHECK HARNESS AND CONNECTOR (DOOR CONTROL RELAY ASSEMBLY - BATTERY AND BODY GROUND)


    1. B007W9IE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Door Control Relay Assembly)

      Disconnect the door control relay assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      q3-7 (GND) - Body ground Always Below 1 Ω
      q4-21 (SEL) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      q3-8 (B) - Body ground Always 11 to 14 V
      q4-9 (IG) - Body ground Ignition switch ON 11 to 14 V
      q4-9 (IG) - Body ground Ignition switch off Below 1 V
      q4-11 (ECUB) - Body ground Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT NO. 2 REAR DOOR WIRE


    1. B007WAPE01
      Text in Illustration
      *a

      No. 2 Rear Door Wire

      (Door Control Relay Assembly Side)
      *b

      No. 2 Rear Door Wire

      (Door Opening Relay Side)

      Disconnect the oq1 and po2 No. 2 rear door wire connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      A-3 - B-6 Always Below 1 Ω
      A-15 - B-7 Always Below 1 Ω
      A-1 - B-3 Always Below 1 Ω

    NG

    REPLACE NO. 2 REAR DOOR WIRE Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (DOOR OPENING RELAY - BATTERY AND BODY GROUND)


    1. B007QZUE08
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Door Opening Relay)

      Disconnect the door opening relay connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      p2-2 (E) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      p2-6 (L) - Body ground Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT POWER SLIDE DOOR MAIN SWITCH


    1. Remove the power slide door main switch Click here.

    2. Inspect the power slide door main switch Click here.


    NG

    REPLACE POWER SLIDE DOOR MAIN SWITCH Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (POWER SLIDE DOOR MAIN SWITCH - DOOR CONTROL RELAY ASSEMBLY AND BODY GROUND)


    1. Disconnect the I29 power slide door main switch connector.

    2. Disconnect the q4 door control relay assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I29-9 - q4-17 (MSW) Always Below 1 Ω
      I29-6 - Body ground Always Below 1 Ω
      I29-9 or q4-17 (MSW) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. INSPECT AUTO SLIDE DOOR CONTROL SWITCH ASSEMBLY


    1. Remove the auto slide door control switch assembly Click here.

    2. Inspect the auto slide door control switch assembly Click here.


    NG

    REPLACE AUTO SLIDE DOOR CONTROL SWITCH ASSEMBLY Click here

    OK

  8. CHECK HARNESS AND CONNECTOR (AUTO SLIDE DOOR CONTROL SWITCH ASSEMBLY - DOOR CONTROL RELAY ASSEMBLY AND BODY GROUND)


    1. Disconnect the I28 auto slide door control switch assembly connector.

    2. Disconnect the q4 door control relay assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I28-4 - q4-16 (DSW) Always Below 1 Ω
      I28-1 - Body ground Always Below 1 Ω
      I28-4 or q4-16 (DSW) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. CHECK HARNESS AND CONNECTOR (SLIDE DOOR MOTOR ASSEMBLY - DOOR CONTROL RELAY ASSEMBLY)


    1. Disconnect the q1 slide door motor assembly connector.

    2. Disconnect the q4 door control relay assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      q1-1 (DSG) - q4-2 (DSG) Always Below 1 Ω
      q1-2 (DS2) - q4-23 (DS2) Always Below 1 Ω
      q1-3 (DSV) - q4-3 (DSV) Always Below 1 Ω
      q1-4 (DS1) - q4-24 (DS1) Always Below 1 Ω
      q1-1 (DSG) or q4-2 (DSG) - Body ground Always 10 kΩ or higher
      q1-2 (DS2) or q4-23 (DS2) - Body ground Always 10 kΩ or higher
      q1-3 (DSV) or q4-3 (DSV) - Body ground Always 10 kΩ or higher
      q1-4 (DS1) or q4-24 (DS1) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  10. INSPECT SLIDE DOOR LOCK RELEASE MOTOR ASSEMBLY


    1. Remove the slide door lock release motor assembly Click here.

    2. Inspect the slide door lock release motor assembly Click here.


    NG

    REPLACE SLIDE DOOR LOCK RELEASE MOTOR ASSEMBLY Click here

    OK

  11. CHECK HARNESS AND CONNECTOR (SLIDE DOOR LOCK RELEASE MOTOR ASSEMBLY - DOOR OPENING RELAY)


    1. Disconnect the p3 slide door lock release motor assembly connector.

    2. Disconnect the p2 door opening relay connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      p3-1 (E) - p2-10 (E) Always Below 1 Ω
      p3-2 (LS2) - p2-12 (P/W) Always Below 1 Ω
      p3-3 (L-) - p2-10 (E) Always Below 1 Ω
      p3-4 (ANRL) - p2-5 (SIG) Always Below 1 Ω
      p3-5 (UL) - p2-1 (UL2) Always Below 1 Ω
      p3-6 (UL3) - p2-3 (UL1) Always Below 1 Ω
      p3-1 (E) or p2-10 (E) - Body ground Always 10 kΩ or higher
      p3-2 (LS2) or p2-12 (P/W) - Body ground Always 10 kΩ or higher
      p3-3 (L-) or p2-10 (E) - Body ground Always 10 kΩ or higher
      p3-4 (ANRL) or p2-5 (SIG) - Body ground Always 10 kΩ or higher
      p3-5 (UL) or p2-1 (UL2) - Body ground Always 10 kΩ or higher
      p3-6 (UL3) or p2-3 (UL1) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  12. CHECK HARNESS AND CONNECTOR (DOOR CONTROL RELAY ASSEMBLY - DOOR OPENING RELAY)


    1. Disconnect the q4 door control relay assembly connector.

    2. Disconnect the p2 door opening relay connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      q4-12 (RACT) - p2-4 (CSW) Always Below 1 Ω
      q4-12 (RACT) - p2-11 (DWN) Always Below 1 Ω
      q4-12 (RACT) or p2-4 (CSW) - Body ground Always 10 kΩ or higher
      q4-12 (RACT) or p2-11 (DWN) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  13. REPLACE DOOR OPENING RELAY


    1. Temporarily replace the door opening relay with a new or normally functioning one Click here.


    NEXT

  14. CHECK OPERATION


    1. Check the operation of the power slide door function Click here.

      OK
      Power slide door function operates normally.

    NG

    REPLACE DOOR CONTROL RELAY ASSEMBLY Click here

    OK

    END (DOOR OPENING RELAY WAS DEFECTIVE)

  15. INSPECT SLIDE DOOR MOTOR ASSEMBLY


    1. Remove the slide door motor assembly Click here.

    2. Inspect the slide door motor assembly Click here.


    NG

    REPLACE SLIDE DOOR MOTOR ASSEMBLY Click here

    OK

  16. CHECK HARNESS AND CONNECTOR (DOOR CONTROL RELAY ASSEMBLY - SLIDE DOOR MOTOR ASSEMBLY)


    1. Disconnect the q3 and q4 door control relay assembly connectors.

    2. Disconnect the q1 and q5 slide door motor assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      q3-2 (CL+) - q5-5 (CL+) Always Below 1 Ω
      q3-6 (CL-) - q5-4 (CL-) Always Below 1 Ω
      q4-2 (DSG) - q1-1 (DSG) Always Below 1 Ω
      q4-3 (DSV) - q1-3 (DSV) Always Below 1 Ω
      q4-23 (DS2) - q1-2 (DS2) Always Below 1 Ω
      q4-24 (DS1) - q1-4 (DS1) Always Below 1 Ω
      q3-2 (CL+) or q5-5 (CL+) - Body ground Always 10 kΩ or higher
      q3-6 (CL-) or q5-4 (CL-) - Body ground Always 10 kΩ or higher
      q4-2 (DSG) or q1-1 (DSG) - Body ground Always 10 kΩ or higher
      q4-3 (DSV) or q1-3 (DSV) - Body ground Always 10 kΩ or higher
      q4-23 (DS2) or q1-2 (DS2) - Body ground Always 10 kΩ or higher
      q4-24 (DS1) or q1-4 (DS1) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE DOOR CONTROL RELAY ASSEMBLY Click here