BLIND SPOT MONITOR SYSTEM FREEZE FRAME DATA

  1. FREEZE FRAME DATA

    1. Whenever a DTC is detected, the blind spot monitor sensor stores the current vehicle (sensor) state as Freeze Frame Data.

    • *1: for LHD

    • *2: for RHD

    CHECK FREEZE FRAME DATA

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) on.

    4. Turn the GTS on.

    5. Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Trouble Codes.

    6. According to the display on the GTS, display the Freeze Frame Data for the selected DTC.

      Body Electrical > Blind Spot Monitor Master

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      Main Switch

      Blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2)

      OFF or ON

      ON: Blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) on

      OFF: Blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) off

      -

      Warning Indicator Turning on(Master)

      State of the outer rear view mirror indicator LH turning on

      OFF or ON

      OFF: The following conditions are not met

      ON: All of the following conditions are met

      • Not during initial check

      • Vehicle detected in left hand side warning area

      • Left turn signal: off

      • Vehicle speed 40 km/h (25 mph) or more

      • Shift lever in any position except R

      • Blind spot monitor warning light not illuminated

      -

      Warning Indicator Flashing(Master)

      State of the outer rear view mirror indicator LH flashing

      OFF or ON

      OFF: The following conditions are not met

      ON: All of the following conditions are met

      • Not during initial check

      • Vehicle detected in left hand side warning area

      • Left turn signal: on

      • Vehicle speed 40 km/h (25 mph) or more

      • Shift lever in any position except R

      • Blind spot monitor warning light not illuminated

      -

      Main Switch Indicator Status

      State of the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2)

      OFF or ON

      OFF: Indicator not illuminated

      ON: Indicator illuminated

      -

      Warning Indicator Input Circuit Voltage

      Outer rear view mirror indicator voltage

      Min.: 0 V, Max.: 25.5 V

      Not illuminated: 0 V

      Illuminated: 2.5 to 7.5 V

      -

      Warning Indicator Input Circuit Current

      Outer rear view mirror indicator current

      Min.: 0 mA, Max.: 255 mA

      Not illuminated: 0 mA

      Illuminated: 5 to 100 mA

      -

      Main Switch Indicator Input Circuit Voltage

      Blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) voltage

      Min.: 0 V, Max.: 25.5 V

      Always: 9 to 16 V

      -

      Turn Switch State

      State of the headlight dimmer switch assembly (turn signal light switch)

      Left ON, Right ON or OFF

      Left ON: Left side of turn signal light switch on

      Right ON: Right side of turn signal light switch on

      OFF: Turn signal light switch off

      -

      Reverse (Only for AT/CVT)

      State of the shift position R signal

      OFF or ON

      ON: Shift lever in R

      OFF: Shift lever in any position except R

      -

      Vehicle Speed

      Vehicle speed signal

      Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)

      Vehicle stopped: 0 km/h (0 mph)

      -

      Steering Angle

      Steering angle sensor

      Min.: -3072°, Max.: 3070.5°

      Left turn: Increases

      Right turn: Decreases

      -

      Power Supply Voltage

      Power supply voltage

      Min.: 0 V, Max.: 50 V

      Always: 11 to 14 V

      -

      Indicator Light Control State

      Outer rear view mirror indicator dimming state

      Dim OFF or Dim ON

      Dim OFF: Indicator not dimmed

      Dim ON: Indicator dimmed

      -

      Angle Adjustment by Auto Alignment

      Angle adjusted using auto alignment

      Min.: Under -12.8 deg, Max.: Over 12.7 deg

      Angle adjusted using auto alignment is displayed

      When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed

      Number of DTC

      Number of DTCs

      Min.: 0, Max.: 255

      When system is normal: 0

      When a malfunction is detected: More than 0

      -

      Body Electrical > Blind Spot Monitor Slave

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      Warning Indicator Turning on(Slave)

      State of the outer rear view mirror indicator RH turning on

      OFF or ON

      OFF: The following conditions are not met

      ON: All of the following conditions are met

      • Not during initial check

      • Vehicle detected in right hand side warning area

      • Right turn signal: OFF

      • Vehicle speed 40 km/h (25 mph) or more

      • Shift lever in any position except R

      • Blind spot monitor warning light not illuminated

      -

      Warning Indicator Flashing(Slave)

      State of the outer rear view mirror indicator RH flashing

      OFF or ON

      OFF: The following conditions are not met

      ON: All of the following conditions are met

      • Not during initial check

      • Vehicle detected in right hand side warning area

      • Vehicle speed 40 km/h (25 mph) or more

      • Right turn signal: ON

      • Shift lever in any position except R

      • Blind spot monitor warning light not illuminated

      -

      Warning Indicator Input Circuit Voltage

      Outer rear view mirror indicator voltage

      Min.: 0 V, Max.: 25.5 V

      Not illuminated: 0 V

      Illuminated: 2.5 to 7.5 V

      -

      Warning Indicator Input Circuit Current

      Outer rear view mirror indicator current

      Min.: 0 mA, Max.: 255 mA

      Not illuminated: 0 mA

      Illuminated: 5 to 100 mA

      -

      Turn Switch State

      State of the headlight dimmer switch assembly (turn signal light switch)

      Left ON, Right ON or OFF

      Left ON: Left side of turn signal light switch on

      Right ON: Right side of turn signal light switch on

      OFF: Turn signal light switch off

      -

      Reverse (Only for AT/CVT)

      State of the shift position R signal

      OFF or ON

      ON: Shift lever in R

      OFF: Shift lever in any position except R

      -

      Vehicle Speed

      Vehicle speed signal

      Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)

      Vehicle stopped: 0 km/h (0 mph)

      -

      Steering Angle

      Steering angle sensor

      Min.: -3072°, Max.: 3070.5°

      Left turn: Increases

      Right turn: Decreases

      -

      Power Supply Voltage

      Power supply voltage

      Min.: 0 V, Max.: 50 V

      Always: 11 to 14 V

      -

      Indicator Light Control State

      Outer rear view mirror indicator dimming state

      Dim OFF or Dim ON

      Dim OFF: Indicator not dimmed

      Dim ON: Indicator dimmed

      -

      Angle Adjustment by Auto Alignment

      Angle adjusted using auto alignment

      Min.: Under -12.8 deg, Max.: Over 12.7 deg

      Angle adjusted using auto alignment is displayed

      When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed

      Number of DTC

      Number of DTCs

      Min.: 0, Max.: 255

      When system is normal: 0

      When a malfunction is detected: More than 0

      -

  3. CLEAR FREEZE FRAME DATA

    Note:

    Clearing the DTCs will also clear the Freeze Frame Data.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) on.

      • *1: for LHD

      • *2: for RHD

    4. Turn the GTS on.

    5. Clear the DTCs and Freeze Frame Data.