VEHICLE STABILITY CONTROL SYSTEM CALIBRATION


  1. DESCRIPTION


    1. After replacing any VSC related components or performing wheel alignment adjustment, clear and read the sensor calibration data.

      Refer to the table below and then perform the necessary operation according to the part to be replaced in order to perform calibration.

    Parts to be Replaced / Operation Necessary Operation
    Skid control ECU (Brake actuator assembly) Perform yaw rate and acceleration sensor zero point calibration and store system information.
    Yaw rate and acceleration sensor (airbag sensor assembly)

    1. Clear zero point calibration data and store system information.

    2. Perform yaw rate and acceleration sensor zero point calibration and store system information.
    Wheel alignment adjustment

    1. Clear zero point calibration data and store system information.

    2. Perform yaw rate and acceleration sensor zero point calibration and store system information.

  2. PERFORM YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION AND STORE SYSTEM INFORMATION

    Note


    • Stored system information cannot be overwritten unless it is cleared. Clear the stored information and then store new system information.

    • While obtaining the zero points, keep the vehicle stationary and do not vibrate, tilt, move, or shake it (do not start the engine).

    • Be sure to perform this procedure on a level surface (with an inclination of less than 1 degree).


    1. Clear the zero point calibration data and store system information.

      Note

      Performing the following procedure will clear the zero points of the yaw rate and acceleration sensor and system information simultaneously.


      1. Turn the ignition switch off.

      2. Check that the steering wheel is centered.

      3. for Automatic Transmission:

        Check that the shift lever is in P and apply the parking brake.

        for Manual Transmission:

        Check that the shift lever is in neutral and apply the parking brake.

      4. Connect the GTS to the DLC3.

      5. Turn the ignition switch to ON.

      6. Turn the GTS on.

      7. Select the skid control ECU (brake actuator assembly) to clear the zero point calibration data using the GTS. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Reset Memory.

      8. Check that the slip indicator light comes on.

      9. Turn the ignition switch off.

        Note

        If the ignition switch is turned to ON for more than 15 seconds with the shift lever in P (for Automatic Transmission) or the parking brake applied (for Manual Transmission) after the zero point of the yaw rate and acceleration sensor has been cleared, only the zero point of the yaw rate sensor will be stored. If the vehicle is driven under these conditions, the skid control ECU (brake actuator assembly) will store the zero point calibration for the acceleration sensor as not being completed. The skid control ECU (brake actuator assembly) will then also indicate this as a malfunction of the VSC system using the indicator light.

    2. Perform the yaw rate and acceleration sensor zero point calibration and store system information.

      Note

      Performing the following procedure will perform the yaw rate and acceleration sensor zero point calibration and store system information simultaneously.


      1. Turn the ignition switch off.

      2. Check that the steering wheel is centered.

      3. for Automatic Transmission:

        Check that the shift lever is in P and apply the parking brake.

        for Manual Transmission:

        Check that the shift lever is in neutral and apply the parking brake.

        Note


        • When Test Mode is selected with the shift lever not in P (for Automatic Transmission) or the parking brake not applied (for Manual Transmission), the yaw rate and acceleration sensor zero point calibration incomplete DTC is stored.

        • When the vehicle is driven with the zero point cleared, the yaw rate and acceleration sensor zero point calibration incomplete DTC is stored.

        • If a DTC is stored that indicates zero point calibration is incomplete, repeat the procedure starting at the step for clearing the zero point calibration data and system information.

      4. Connect the GTS to the DLC3.

      5. Turn the ignition switch to ON.

      6. Turn the GTS on.

      7. Switch the skid control ECU (brake actuator assembly) to Test Mode using the GTS. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Test Mode.

      8. After the Test Mode has been entered, keep the vehicle stationary on a level surface for 5 seconds or more.

      9. Check that the slip indicator light comes on for several seconds and then blinks in the Test Mode pattern.

        Tech Tips


        • If the slip indicator light does not blink, perform zero point calibration again.

        • The zero point calibration is performed only once after the system enters the Test Mode.

        • Calibration cannot be performed again until the stored data is cleared.

      10. Turn the ignition switch off and disconnect the GTS.