PRE-COLLISION SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Pre-Collision 2 / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Pre-Collision 2 > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Turn Light RH Turn signal switch (right) status ON or OFF

      ON: Turn signal switch (right) on

      OFF: Turn signal switch (right) off

      		 -
      Turn Light LH Turn signal switch (left) status ON or OFF

      ON: Turn signal switch (left) on

      OFF: Turn signal switch (left) off

      		 -
      PCS OFF Switch Pre-collision system on/off status ON or OFF

      ON: Pre-collision system on

      OFF: Pre-collision system off

      		 -
      PCS Indicator

      • "Pre-Collision Safety Malfunction Visit Your Dealer" display request signal*1

      • "PRE-COLLISION SAFETY MALFUNCTION VISIT YOUR DEALER" display request signal*2

      		 ON or OFF

      • ON: "Pre-Collision Safety Malfunction Visit Your Dealer" display requested*1

      • OFF: "Pre-Collision Safety Malfunction Visit Your Dealer" display not requested*1


      • ON: "PRE-COLLISION SAFETY MALFUNCTION VISIT YOUR DEALER" display requested*2

      • OFF: "PRE-COLLISION SAFETY MALFUNCTION VISIT YOUR DEALER" display not requested*2

      		 -
      PCS Disabled Indicator

      • "Pre-Collision Safety Unavailable" display request signal*1

      • "PRE-COLLISION SAFETY UNAVAILABLE" display request signal*2

      		 ON or OFF

      • ON: "Pre-Collision Safety Unavailable" display requested*1

      • OFF: "Pre-Collision Safety Unavailable" display not requested*1


      • ON: "PRE-COLLISION SAFETY UNAVAILABLE" display requested*2

      • OFF: "PRE-COLLISION SAFETY UNAVAILABLE" display not requested*2

      		 -
      Pre-Collision Safety Warning Buz Pre-collision system warning buzzer Valid or Inval

      Valid: Pre-collision system warning buzzer operation possible

      Inval: Pre-collision system warning buzzer operation not possible

      		 -
      Pre-Collision Brake Pre-collision brake function Valid or Inval

      Valid: Pre-collision brake operation possible

      Inval: Pre-collision brake operation not possible

      		 -
      PBA Start Pre-collision brake assist activation signal OFF, Standby, Assist Lv1 or Assist Lv2

      OFF: Pre-collision brake assist not operating

      Standby: Brake pedal not depressed during pre-collision brake assist operation

      Assist Lv1: Brake pedal depressed during pre-collision brake assist operation

      Assist Lv2: Brake pedal firmly depressed during pre-collision brake assist operation

      		 Signal status changes when the pre-collision brake assist is activated before a crash (Pre-collision brake will activate only in situations where the driver depresses the brake pedal)
      Brake Assist Standby - - - This item is displayed on the GTS but is not used.
      Pre-Collision Brake Control Pre-collision brake operational status ON or OFF

      ON: Pre-collision brake operating

      OFF: Pre-collision brake not operating

      		 -
      AVS Start - - - This item is displayed on the GTS but is not used.
      VGRS Start - - - This item is displayed on the GTS but is not used.
      PBA Control Pre-collision brake assist operational status Valid or Invalid

      Valid: Pre-collision brake assist control operation possible

      Invalid: Pre-collision brake assist control operation not possible

      		 -
      Pre-Collision Safety Brake Ind Pre-collision system alarm warning message status ON or OFF

      ON: Displayed

      OFF: Not displayed

      		 "BRAKE!" is displayed
      PCS Collision Alarm Buzzer Skid control buzzer status ON or OFF

      ON: Skid control buzzer sounding

      OFF: Skid control buzzer not sounding

      		 -
      Front Radar-Dirt History Millimeter wave radar sensor assembly dirt history ON or OFF

      ON: History of excessive dirt

      OFF: No history of excessive dirt

      		 -
      Front Radar-Environment Hist Millimeter wave radar sensor assembly environment signal Good or Bad

      Good: Millimeter wave radar sensor assembly environment good

      Bad: Millimeter wave radar sensor assembly environment bad

      		 -
      Front Radar-Temperature Malfunction History Millimeter wave radar sensor assembly abnormal temperature history ON or OFF

      ON: History of abnormal temperature

      OFF: No history of abnormal temperature

      		 -
      Front Radar-Low Voltage History Millimeter wave radar sensor assembly low voltage history ON or OFF

      ON: History of low voltage

      OFF: No history of low voltage

      		 If the engine starts 1 second or more after the ignition switch was turned ON, this item may change to ON
      Front Recognition Camera-Blockage History Forward recognition camera obstruction history ON or OFF

      ON: History of being obstructed

      OFF: No history of being obstructed

      		 -
      Front Recognition Camera-Malfunction History Forward recognition camera system unavailable history ON or OFF

      ON: History of unavailable

      OFF: No history of unavailable

      		 -
      Destination Variation No Destination country for millimeter wave radar sensor assembly 0 or Not Available Not Available -
      Control Mode ECU control mode status Normal or Check Mode

      Normal: Normal operation

      Check Mode: Operating in Control Mode

      		 -
      PCS Operation State Retention Setting PCS Operation State Retention Setting customize setting ON or OFF

      ON: Customize setting set to ON

      OFF: Customize setting set to OFF

      		 -
      PCS Alarm Activation Distance Retention Setting 1 PCS Alarm Activation Distance Retention Setting 1 customize setting ON or OFF

      ON: Customize setting set to ON

      OFF: Customize setting set to OFF

      		 -
      PCS Alarm Activation Distance Retention Setting 2 PCS Alarm Activation Distance Retention Setting 2 customize setting ON or OFF

      ON: Customize setting set to ON

      OFF: Customize setting set to OFF

      		 -
      PCS Alarm Activation Distance Retention Setting 3 PCS Alarm Activation Distance Retention Setting 3 customize setting ON or OFF

      ON: Customize setting set to ON

      OFF: Customize setting set to OFF

      		 -
      The Number of DTCs Number of past trouble codes min: 0, max: 255 Number of DTCs will be displayed -

      • *1: for TFT Display Type

      • *2: for Dot Display Type

    6. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    7. Read the Data List according to the display on the GTS.


      Chassis > ABS/VSC/TRC > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Stop Light Relay Output Stop light control relay (STOP/CDS FAN Relay) output ON or OFF

      ON: Relay output on (Stop lights on)

      OFF: Relay output off (Stop lights off)

      		 -

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Pre-Collision 2 / Active Test.

    5. Perform the Active Test according to the display on the GTS.


      Body Electrical > Pre-Collision 2 > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      PCS Collision Alarm Buzzer Skid control buzzer ON / OFF

      Test possible with ignition switch to ON

      Vehicle condition: Vehicle stopped

    6. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    7. Perform the Active Test according to the display on the GTS.


      Chassis > ABS/VSC/TRC > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Stop Light Relay Stop light control relay (STOP/CDS FAN Relay) Relay ON/OFF

      Stop lights come on

      Vehicle condition: Vehicle stopped

    8. Enter the following menus: Body Electrical / Combination Meter / Active Test.

    9. Perform the Active Test according to the display on the GTS.


      Body Electrical > Combination Meter > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Indicat. Precrash PCS warning light ON / OFF -