POWER WINDOW CONTROL SYSTEM Driver Side Power Window does not Operate with Power Window Master Switch

DTC Code DTC Name
Driver Side Power Window does not Operate with Power Window Master Switch

DESCRIPTION

  • If the manual up/down function does not operate, there may be a malfunction in the power window regulator master switch, door window regulator, harness or connector.

WIRING DIAGRAM

B225718E04

CAUTION / NOTICE / HINT

Note:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE

  1. CHECK LIN COMMUNICATION SYSTEM

    1. Check for LIN communication system DTCs related to the power window control system (Click here).

      OK

      LIN communication system DTCs are not output.

    GO TO LIN COMMUNICATION SYSTEM

    (Click here)

  2. CHECK FOR DTC (B2312)

    1. Check if DTC B2312 is output (Click here).

      OK

      DTC B2312 is not output.

    GO TO DTC B2312

    (Click here)

  3. READ VALUE USING INTELLIGENT TESTER (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)

    1. Use the Data List to check if the power window regulator master switch is functioning properly (Click here).

      Table 1. D-Door Motor

      Tester Display

      Measurement Item/Range

      Normal Condition

      Diagnostic Note

      D Door P/W Up SW

      Driver side power window manual up signal / ON or OFF

      ON: Driver side power window manual up switch operated

      OFF: Driver side power window switch not operated

      -

      D Door P/W Down SW

      Driver side power window manual down signal / ON or OFF

      ON: Driver side power window manual down switch operated

      OFF: Driver side power window switch not operated

      -

      OK

      The display changes according to operation of the power window regulator master switch.

      Table 2. Result

      Result

      Proceed to

      OK (for LHD)

      A

      OK (for RHD)

      B

      NG

      C

    REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY LH

    (Click here)

    REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY RH

    (Click here)

  4. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)

    1. B217667E05

      Disconnect the K5*1 or J5*2 switch connector.

      • *1: for LHD

      • *2: for RHD

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Standard Voltage

      Table 3. for LHD

      Tester Connection

      Condition

      Specified Condition

      K5-11 (B) - Body ground

      Always

      11 to 14 V
      Table 4. for RHD

      Tester Connection

      Condition

      Specified Condition

      J5-11 (B) - Body ground

      Always

      11 to 14 V

      Standard Resistance

      Table 5. for LHD

      Tester Connection

      Condition

      Specified Condition

      K5-12 (GND) - Body ground

      Always

      Below 1 Ω
      Table 6. for RHD

      Tester Connection

      Condition

      Specified Condition

      J5-12 (GND) - Body ground

      Always

      Below 1 Ω
      Table 7. Text in Illustration

      *1

      for LHD

      *2

      for RHD

      *3

      Front view of wire harness connector

      (to Power Window Regulator Master Switch)

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  5. CHECK HARNESS AND CONNECTOR (FRONT DOOR WINDOW REGULATOR ASSEMBLY - BATTERY AND BODY GROUND)

    1. B216017E08

      Disconnect the K8*1 or J6*2 regulator connector.

      • *1: for LHD

      • *2: for RHD

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Standard Voltage

      Table 8. for LHD

      Tester Connection

      Condition

      Specified Condition

      K8-2 (B) - Body ground

      Always

      11 to 14 V
      Table 9. for RHD

      Tester Connection

      Condition

      Specified Condition

      J6-2 (B) - Body ground

      Always

      11 to 14 V

      Standard Resistance

      Table 10. for LHD

      Tester Connection

      Condition

      Specified Condition

      K8-1 (GND) - Body ground

      Always

      Below 1 Ω
      Table 11. for RHD

      Tester Connection

      Condition

      Specified Condition

      J6-1 (GND) - Body ground

      Always

      Below 1 Ω
      Table 12. Text in Illustration

      *1

      for LHD

      *2

      for RHD

      *3

      Front view of wire harness connector

      (to Front Door Window Regulator)

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT DOOR WINDOW REGULATOR ASSEMBLY)

    • *1: for LHD

    • *2: for RHD

    1. B215962E09

      Disconnect the K5*1 or J5*2 switch connector.

    2. Disconnect the K8*1 or J6*2 regulator connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Table 13. for LHD

      Tester Connection

      Condition

      Specified Condition

      K5-20 (UP) - K8-10 (UP)

      Always

      Below 1 Ω

      K5-15 (DOWN) - K8-7 (DOWN)

      Always

      Below 1 Ω

      K5-20 (UP) or K8-10 (UP) - Body ground

      Always

      10 kΩ or higher

      K5-15 (DOWN) or K8-7 (DOWN) - Body ground

      Always

      10 kΩ or higher
      Table 14. for RHD

      Tester Connection

      Condition

      Specified Condition

      J5-20 (UP) - J6-10 (UP)

      Always

      Below 1 Ω

      J5-15 (DOWN) - J6-7 (DOWN)

      Always

      Below 1 Ω

      J5-20 (UP) or J6-10 (UP) - Body ground

      Always

      10 kΩ or higher

      J5-15 (DOWN) or J6-7 (DOWN) - Body ground

      Always

      10 kΩ or higher
      Table 15. Text in Illustration

      *1

      for LHD

      *2

      for RHD

      *3

      Front view of wire harness connector

      (to Power Window Regulator Master Switch)

      *4

      Front view of wire harness connector

      (to Front Door Window Regulator)
      Table 16. Result

      Result

      Proceed to

      OK (for LHD)

      A

      OK (for RHD)

      B

      NG

      C

    INSPECT FRONT DOOR WINDOW REGULATOR ASSEMBLY RHClick here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  7. INSPECT FRONT DOOR WINDOW REGULATOR ASSEMBLY LH

    B216566E02

    1. Remove the door window regulator (Click here).

    2. Check that the window regulator moves smoothly as follows.

      Note:

      • Do not apply positive (+) battery voltage to any terminal other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

      • Reset the door window regulator (initialize the pulse sensor) after installing the door window regulator to the door.

      OK

      Measurement Condition

      Specified Condition

      1. Connect the positive (+) battery terminal to terminal 2 (B), and connect the negative (-) battery terminal to terminal 1 (GND), and keep them connected for 3 seconds or more.

      2. With terminals 2 (B) and 1 (GND) connected to the battery, connect the negative (-) battery terminal to terminal 10 (UP).

      3. Disconnect and reconnect the negative (-) battery terminal to terminal 10 (UP) within 1 second.

      Arm of window regulator rotates clockwise (Up)

      1. Connect the positive (+) battery terminal to terminal 2 (B), and connect the negative (-) battery terminal to terminal 1 (GND), and keep them connected for 3 seconds or more.

      2. With terminals 2 (B) and 1 (GND) connected to the battery, connect the negative (-) battery terminal to terminal 7 (DOWN).

      3. Disconnect and reconnect the negative (-) battery terminal to terminal 7 (DOWN) within 1 second.

      Arm of window regulator rotates counterclockwise (Down)

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

    (Click here)

    REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY LH

    (Click here)

  8. INSPECT FRONT DOOR WINDOW REGULATOR ASSEMBLY RH

    1. B216565E02

      Remove the door window regulator (Click here).

    2. Check that the window regulator moves smoothly as follows.

      Note:

      • Do not apply positive (+) battery voltage to any terminal other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

      • Reset the door window regulator (initialize the pulse sensor) after installing the door window regulator to the door.

      OK

      Measurement Condition

      Specified Condition

      1. Connect the positive (+) battery terminal to terminal 2 (B), and connect the negative (-) battery terminal to terminal 1 (GND), and keep them connected for 3 seconds or more.

      2. With terminals 2 (B) and 1 (GND) connected to the battery, connect the negative (-) battery terminal to terminal 10 (UP).

      3. Disconnect and reconnect the negative (-) battery terminal to terminal 10 (UP) within 1 second.

      Arm of window regulator rotates counterclockwise (Up)

      1. Connect the positive (+) battery terminal to terminal 2 (B), and connect the negative (-) battery terminal to terminal 1 (GND), and keep them connected for 3 seconds or more.

      2. With terminals 2 (B) and 1 (GND) connected to the battery, connect the negative (-) battery terminal to terminal 7 (DOWN).

      3. Disconnect and reconnect the negative (-) battery terminal to terminal 7 (DOWN) within 1 second.

      Arm of window regulator rotates clockwise (Down)

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

    (Click here)

    REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY RH

    (Click here)