FRONT SEAT OUTER BELT ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE DOOR SCUFF PLATE ASSEMBLY LH

    Click here

  4. REMOVE REAR DOOR SCUFF PLATE LH

    Click here

  5. REMOVE LAP BELT OUTER ANCHOR COVER


    1. B008HMB

      Detach the 2 claws, guide and remove the lap belt outer anchor cover.

  6. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. B008J1M

      Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly LH.

  7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  8. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    Click here

  9. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    Click here

  10. REMOVE LOWER CENTER PILLAR GARNISH LH

    Click here

  11. REMOVE CENTER PILLER GARNISH ASSEMBLY LH

    Click here

  12. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH


    1. B008I82

      Remove the nut and disconnect the shoulder anchor of the front seat outer belt assembly LH.

    2. B008J3ZC01
      *1 Protective Tape
      *2 Locking Button

      Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    3. Disconnect the connector.

    4. B008IVC

      Remove the bolt.

    5. Detach the 2 guides and remove the front seat outer belt assembly LH.

  13. REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH (for Front Passenger Seat Belt with Selectable Force Limiter)


    1. B008I82

      Remove the nut and shoulder anchor of the front seat outer belt assembly RH.

    2. B008J36C01
      *1 Protective Tape
      *2 Locking Button

      Using a screwdriver, pull out the 2 locking buttons in the direction shown by the arrow in the illustration to release the 2 locks and disconnect the pretensioner connector and selectable force limiter connector as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    3. Disconnect the connector.

    4. B008IJM

      Remove the bolt.

    5. Detach the 2 guides to remove the front seat outer belt assembly RH.

  14. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH


    1. B008H70

      Detach the 6 guides and remove the front shoulder belt anchor plate sub-assembly LH.

  15. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY


    1. B008JE7

      Remove the 2 bolts.

    2. Disconnect the guide to remove the front shoulder belt anchor adjuster assembly LH.