MANUAL TRANSMISSION ASSEMBLY (for 1KD-FTV) REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  2. DRAIN MANUAL TRANSMISSION OIL


    1. Remove the filler plug and gasket.

    2. Remove the drain plug and gasket, and drain the oil.

    3. Install the drain plug with a new gasket.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  3. REMOVE FRONT EXHAUST PIPE ASSEMBLY (w/o DPF)


    1. B007UN3

      Remove the 2 bolts and 2 compression springs.

    2. Disconnect the No. 4 exhaust pipe support and front exhaust pipe.

    3. Remove the gasket.

  4. REMOVE FRONT EXHAUST PIPE ASSEMBLY (w/ DPF)

    Click here

  5. REMOVE PROPELLER SHAFT ASSEMBLY (for Long Wheelbase)

    Click here

  6. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Super Long Wheelbase)

    Click here

  7. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF)


    1. B007SXB

      Remove the 2 bolts and No. 2 exhaust manifold heat insulator.

  8. REMOVE NO. 3 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF)


    1. B007VK0

      Remove the 2 bolts and No. 3 exhaust manifold heat insulator.

  9. REMOVE CATALYTIC WITH PIPE CONVERTER ASSEMBLY (w/ DPF)


    1. B007U91

      Remove the 2 nuts from the catalytic with pipe converter assembly.

    2. B007U98

      Remove the 3 nuts, catalytic with pipe converter assembly and gasket.

  10. REMOVE TURBINE OUTLET ELBOW STAY


    1. B007RVK

      w/ DPF:

      Remove the 2 bolts and turbine outlet elbow stay.

    2. B007RRO

      w/o DPF:

      Remove the 2 bolts, 2 nuts and turbine outlet elbow stay.

  11. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/o DPF)


    1. B007OWY

      Remove the 3 nuts, exhaust manifold converter sub-assembly and gasket.

  12. REMOVE TRANSMISSION CONTROL CABLE INSULATOR (for RHD)


    1. B007OMA

      Remove the nut and No. 1 transmission control cable insulator from the select outer lever.

    2. Remove the 2 nut and No. 2 transmission control cable insulator from the No. 1 transmission control cable bracket.

  13. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    1. B007VCTE02

      Put matchmarks on the transmission control cable assembly and the select outer lever.

    2. Put matchmarks on the transmission control cable assembly and the shift outer lever.

    3. Remove the nut and disconnect the transmission control cable assembly from the select outer lever.

    4. Remove the nut and disconnect the transmission control cable assembly from the shift outer lever.

    5. B007UDO

      Using a screwdriver, disengage the claws of the 2 clips.

    6. Remove the 2 transmission control cable assemblies and 2 clips from the No. 1 transmission control cable bracket.

  14. DISCONNECT WIRE HARNESS


    1. Disconnect the back-up light switch connector.

    2. Disconnect the speed sensor connector.

    3. Remove the bolt and separate the ground cable.

  15. SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY


    1. B007SW0

      Remove the 2 bolts and separate the clutch release cylinder assembly.

  16. REMOVE STARTER ASSEMBLY (for 2.2 kW Type)


    1. B007V15E01

      for Wide Body:

      Remove the bolt and ground cable.

    2. B007SEG

      Open the terminal cap.

    3. Remove the nut and disconnect the wire harness from terminal 30.

    4. Disconnect the terminal 50 connector from the starter.

    5. B007V17

      for Automatic Transmission:


      1. Remove the bolt, 2 nuts and starter.

    6. B007TCE

      for Manual Transmission:


      1. Remove the bolt, nut and starter.

  17. REMOVE STARTER ASSEMBLY (for 2.7 kW Type)


    1. B007V15E01

      for Wide Body:

      Remove the bolt, then disconnect the ground cable.

    2. B007QWSE01

      Open the terminal cap.

    3. Remove the nut and disconnect the wire harness from terminal 30.

    4. Disconnect the terminal 50 connector from the starter.

    5. B007V7W

      for Automatic Transmission:

      Remove the bolt and 2 nuts, then remove the starter.

    6. B007VMZ

      for Manual Transmission:

      Remove the bolt and nut, then remove the starter.

  18. REMOVE MANUAL TRANSMISSION ASSEMBLY


    1. B007R0C

      Support the manual transmission assembly with a transmission jack.

    2. Remove the bolt, nut, and 2 washers, and then separate the transmission from the frame.

    3. B007PA8E01

      Remove the 9 bolts, manual transmission unit, No. 1 control cable bracket, rear end plate, and cylinder block insulator.

      Tech Tips


      • The A bolts in the illustration tighten the control cable bracket together.


      • The B bolts in the illustration tighten the stiffener plate together.


      • Bolt C in the illustration tightens the harness clamp bracket together.

  19. REMOVE EXTENSION HOUSING DYNAMIC DAMPER (WITH DYNAMIC DAMPER)


    1. B007Q1Y

      Remove the 4 bolts and extension housing dynamic damper.

  20. REMOVE REAR ENGINE MOUNTING INSULATOR ASSEMBLY


    1. B007V53

      Remove the 4 bolts and rear engine mounting insulator assembly.