FRONT SEAT OUTER BELT ASSEMBLY INSTALLATION


  1. INSTALL SHOULDER BELT ANCHORAGE PLATE COVER (for Extra Cab and Double Cab)

    A01DWJ6E05

    1. Install the plate cover as shown in the illustration.

      Tech Tips

      Make sure the plate cover is firmly set into the garnish's claws.

  2. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY (for Extra Cab and Double Cab)

    A01E0Q6E01

    1. Insert the tip of the adjuster to the pillar, and align the adjuster's bolt hole to the pillar's bolt hole.

    2. Install the bolt as shown in the illustration.

      Torque:
      42
      N*m  { 428 kgf*cm, 31 ft.*lbf }

    3. Install the center pillar garnish Click here.

    4. Install the quarter pillar garnish Click here.

  3. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

    A01E1BRE02

    Note

    Do not disassemble the retractor.


    1. w/o Pretensioner single cab and extra cab:

      Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    2. A01DWQOE03

      w/o Pretensioner Double cab:

      Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

      Torque:
      4.8 N*m  { 49 kgf*cm, 42 in.*lbf }
    3. A01DVG8E05

      w/ Pretensioner:

      Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.


      1. for Single Cab and Extra Cab:

        Install the seat belt with the 2 bolts A and B.

        Torque:
        4.8 N*m  { 49 kgf*cm, 42 in.*lbf, for bolt A }
        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf, for bolt B }

      2. for Double Cab:

        Install the seat belt with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf, for bolt B }
    4. A01E1QQ

      Connect the pretensioner connector as shown in the illustration.

    5. A01E2MXE02

      Single cab:

      Install the anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    6. Close the cover.

    7. A01DUXKE02

      Extra cab and double cab:

      Install the anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    8. Install the cap.

    9. A01DWIKE03

      Single cab:

      Install the quarter trim panel lower. Then install the seat belt floor anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    10. A01E1MGE02

      Extra cab:

      Install the quarter inside trim board. Then install the seat belt floor anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    11. A01DVKRE02

      Double cab:

      Install the anchor of the seat belt with the built-in bolt after installing the center pillar garnish lower.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.