REAR SEAT OUTER BELT ASSEMBLY DISPOSAL

CAUTION / NOTICE / HINT

Tech Tips

When scrapping vehicles equipped with a seat belt pretensioner or disposing of a seat belt (with a seat belt pretensioner), always deploy the seat belt pretensioner first in accordance with the procedure described below. If any abnormality occurs during deployment of the seat belt pretensioner, contact the SERVICE DEPARTMENT of the distributor.

PROCEDURE


  1. DISPOSE OF REAR NO.1 SEAT OUTER BELT ASSEMBLY LH (When Installed in Vehicle) (When Installed in Vehicle)

    CAUTION:


    • Use gloves and safety glasses when handling a rear No. 1 seat outer belt with a deployed pretensioner.

    • Always wash your hands with water after completing the operation.

    • Do not apply water, etc. to a rear No. 1 seat outer belt with a deployed pretensioner.

    • When deploying the seat belt pretensioner, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical interference.

    Note


    • When disposing of a rear No. 1 seat outer belt with a pretensioner, never deploy the pretensioner in the customer's vehicle.

    • Never dispose of a rear No. 1 seat outer belt assembly with a pretensioner that has not been deployed.

    • The seat belt pretensioner produces an exploding sound when it deploys, so perform the operation outdoors where it will not disturb local residents.

    • When deploying a rear No. 1 seat outer belt (with a seat belt pretensioner), perform the operation at least 10 m (33 ft.) away from the rear No. 1 seat outer belt.

    • Be sure to follow the procedure listed below when deploying the seat belt pretensioner.


    1. B008HHGN01

      Check the function of SST.

      SST
      09082-00700

      CAUTION:

      When deploying the seat belt pretensioner, always use the specified SST.


      1. B008HAAC11
        *1 Battery

        Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

        Tech Tips

        At this time, do not connect the yellow connector. It will be connected to the seat belt pretensioner in a later step.

      2. B008JEQN01

        Press the SST deployment switch and check that the LED of the SST deployment switch illuminates.

        CAUTION:

        If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST.

    2. Disconnect the rear No. 1 seat outer belt pretensioner connector.


      1. Disconnect the cable from the negative (-) battery terminal.

        CAUTION:

        Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      2. Remove the deck trim side panel assembly.

        Click here

      3. Connect the floor anchor of the rear No. 1 seat outer belt assembly with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }
      4. B008IOPC01
        *1 Locking Button
        *2 Protective Tape

        Using a screwdriver, pull out the locking button in the direction shown by the arrow in the illustration to release the lock, and disconnect the pretensioner connector as shown in the illustration.

        Tech Tips

        Tape the screwdriver tip before use.

    3. Connect SST.

      SST
      09082-00700

      1. B008H59C01

        Connect 2 SST, and then connect them to the rear No. 1 seat outer belt pretensioner.

        Note

        To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.

      2. B008IOSC24
        *a 10 m or more

        Move SST at least 10 m (33 ft.) away from the front of the vehicle.

      3. Close all the doors and windows of the vehicle.

        Note

        Do not damage the SST wire harness.

    4. Deploy the rear No. 1 seat outer belt pretensioner.


      1. Confirm that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.

      2. Connect the red clip of SST to the battery positive (+) terminal and the black clip to the negative (-) terminal.

      3. Press the SST deployment switch to deploy the rear No. 1 seat outer belt pretensioner.

        Tech Tips

        The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.

    5. B00572J

      Dispose of the rear No. 1 seat outer belt assembly.


      1. Remove the rear No. 1 seat outer belt assembly and SST.

      2. Place the rear No. 1 seat outer belt in a plastic bag, tie the end tightly, and dispose of it in the same way as other general parts.

        CAUTION:


        • The rear No. 1 seat outer belt becomes very hot when the rear No. 1 seat outer belt pretensioner is deployed, so leave it untouched for at least 30 minutes after it has been deployed.

        • Use gloves and safety glasses when handling a rear No. 1 seat outer belt with a pretensioner that has been deployed.

        • Always wash your hands with water after completing the operation.

        • Do not apply water, etc. to a rear No. 1 seat outer belt assembly with a pretensioner that has been deployed.

        Tech Tips

        When scrapping a vehicle, deploy the rear No. 1 seat outer belt pretensioners, and then scrap the vehicle with the deployed outer belt installed.

  2. DISPOSE OF REAR NO.1 SEAT OUTER BELT ASSEMBLY LH (When not Installed in Vehicle) (When not Installed in Vehicle)

    CAUTION:


    • Use gloves and safety glasses when handling a rear No. 1 seat outer belt with a deployed pretensioner.

    • Always wash your hands with water after completing the operation.

    • Do not apply water, etc. to a rear No. 1 seat outer belt with a deployed pretensioner.

    • When deploying a seat belt pretensioner, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical interference.

    Note


    • When disposing of a rear No. 1 seat outer belt with a pretensioner, never deploy the pretensioner in the customer's vehicle.

    • Never dispose of a rear No. 1 seat outer belt assembly with a pretensioner that has not been deployed.

    • The seat belt pretensioner produces an exploding sound when it deploys, so perform the operation outdoors where it will not disturb local residents.

    • When deploying a rear No. 1 seat outer belt (with a seat belt pretensioner), perform the operation at least 10 m (33 ft.) away from the rear No. 1 seat outer belt.

    • Be sure to follow the procedure listed below when deploying the seat belt pretensioner.


    1. B008HHGN01

      Check the function of SST.

      SST
      09082-00700

      CAUTION:

      When deploying the seat belt pretensioner, always use the specified SST.


      1. B008HAAC11
        *1 Battery

        Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

        Tech Tips

        At this time, do not connect the yellow connector. It will be connected to the seat belt pretensioner in a later step.

      2. B008JEQN01

        Press the SST deployment switch and check that the LED of the SST deployment switch illuminates.

        CAUTION:

        If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Remove the rear No. 1 seat outer belt assembly.

      Click here

    4. B008JJQC03
      *a Cut
      *b 100 mm

      Wind the seat belt webbing with the retractor.

    5. When the seat belt webbing is sufficiently wound, cut the seat belt webbing approximately 100 mm (3.94 in.) from the retractor as shown in the illustration.

      Tech Tips

      The retractor resistance increases in correlation with how much the seat belt webbing is wound.

    6. B008H59C01

      Connect SST.

      SST
      09082-00700

      1. Connect 2 SST, and then connect them to the rear No. 1 seat outer belt pretensioner.

        Note

        To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.

      2. B008HK7C01

        Place the rear No. 1 seat outer belt on the ground and cover it with a tire and wheel assembly.

        Note


        • Position the rear No. 1 seat outer belt assembly as shown in the illustration.

        • Use a scrap tire and wheel assembly when disposing of a seat belt pretensioner.

      3. Position and hold SST at least 10 m (33 ft.) away from the wheel.

        Note

        Do not damage the SST wire harness.

    7. B008HYEC01
      *a 10 m or more

      Deploy the rear No. 1 seat outer belt pretensioner.


      1. Check that no one is within a 10 m (33 ft.) radius of the wheel.

      2. Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

      3. Press the SST deployment switch to deploy the seat belt pretensioner.

        Tech Tips

        The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.

    8. B00572J

      Dispose of the rear No. 1 seat outer belt assembly.


      1. Remove the wheel and SST.

      2. Place the rear No. 1 seat outer belt in a plastic bag, tie the end tightly, and dispose of it in the same way as other general parts.

        CAUTION:


        • The rear No. 1 seat outer belt becomes very hot when the rear No. 1 seat outer belt pretensioner is deployed, so leave it untouched for at least 30 minutes after it has been deployed.

        • Use gloves and safety glasses when handling a rear No. 1 seat outer belt with a pretensioner that has been deployed.

        • Always wash your hands with water after completing the operation.

        • Do not apply water, etc. to a rear No. 1 seat outer belt assembly with a pretensioner that has been deployed.

        Tech Tips

        When scrapping a vehicle, deploy the rear No. 1 seat outer belt pretensioners, and then scrap the vehicle with the deployed outer belt installed.