STOP AND START SYSTEM(for V35A-FTS), Diagnostic DTC:P253014

DTC Code DTC Name
P253014 Ignition Switch Circuit Short to Ground or Open

DESCRIPTION

If the engine stop and start ECU receives the off signal from the certification ECU (smart key ECU assembly) when communication with the ECM is normal, the engine stop and start ECU will store DTC P253014.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P253014 Ignition Switch Circuit Short to Ground or Open

All of the following conditions are met for 10 seconds or more (1 trip detection logic):


  • Engine switch off signal is input.

  • Communication with the ECM is normal.

  • Engine switch (communication) to on (IG).

  • Wire harness or connector

  • IG2 P relay (Passenger side Junction block assembly)

  • BBC relay

  • Certification ECU (Smart key ECU assembly)

  • Engine stop and start ECU

 Does not come on DTC stored SAE Code: P2531

CONFIRMATION DRIVING PATTERN


  1. Tech Tips


    • If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

      In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (52°F) or higher, the refresh charge will be completed.)

    • If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

      If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

    • After the refresh charge completes, turn the engine switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

    • Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.

    CONFIRMATION AFTER TROUBLESHOOTING


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Stop and Start > Clear DTCs

    5. Start the engine and warm it up.

    6. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.

    7. Depress the brake pedal and stop the vehicle.

    8. Keep the engine stopped by stop and start control for 10 second or more. (Keep the shift lever in D.)

    9. Release the brake pedal with the shift lever in D to start the engine.

    10. Check that DTCs are not output.


      Powertrain > Stop and Start > Trouble Codes

  2. STOP AND START SYSTEM OPERATION CHECK

    Tech Tips


    • If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

      In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (52°F) or higher, the refresh charge will be completed.)

    • If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

      If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

    • After the refresh charge completes, turn the engine switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.


    1. Start the engine and warm it up.

    2. Turn the air conditioning system off.

    3. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.

    4. Depress the brake pedal and stop the vehicle.

    5. Allow the engine to stop by stop and start control. (Keep the shift lever in D.)

    6. Release the brake pedal with the shift lever in D to start the engine.

WIRING DIAGRAM

B006DOZE01
B006DOZE02

CAUTION / NOTICE / HINT

Note


  • Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

    Click here

  • After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

    Click here

  • After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Tech Tips


  • Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

    Click here

  • DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

    Click here

PROCEDURE


  1. READ VALUE USING GTS (IG SWITCH)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Stop and Start / Data List / IG Switch.


      Powertrain > Stop and Start > Data List
      Tester Display
      IG Switch

    5. According to the display on the GTS, read the Data List.

      Result
      Tester Display Result Proceed to
      IG Switch ON A
      OFF B

    A

    USE SIMULATION METHOD TO CHECK Click here

    B

  2. CHECK HARNESS AND CONNECTOR (IG2 TERMINAL POWER SOURCE CIRCUIT)


    1. Disconnect the engine stop and start ECU connector.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      G84-18 (IG2) - Body ground Engine switch on (IG) 9.5 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - PASSENGER SIDE JUNCTION BLOCK ASSEMBLY) Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (+B TERMINAL POWER SOURCE CIRCUIT)


    1. Disconnect the engine stop and start ECU connector.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A34-1 (+B) - Body ground Engine switch on (IG) 9.5 to 14 V
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ENGINE STOP AND START ECU Click here

    NG

  4. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BBC RELAY)


    1. Disconnect the A34 engine stop and start ECU connector.

    2. Remove the BBC relay from No. 2 engine room relay block.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A34-1 (+B) - BBC relay terminal 5 Always Below 1 Ω
      A34-1 (+B) - Body ground Always 10 kΩ or higher
      BBC relay terminal 5 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT RELAY (BBC RELAY)


    1. Inspect the BBC relay.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE RELAY (BBC RELAY)

    OK

  6. CHECK HARNESS AND CONNECTOR (BBC RELAY - BODY GROUND)


    1. Remove the BBC relay from No. 2 engine room relay block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      BBC relay terminal 1 - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK HARNESS AND CONNECTOR (BBC RELAY - BATTERY)

    B006F30C01
    *1 No. 2 Engine Room Relay Block
    *a BBC Relay Terminal

    1. Remove the BBC relay from No. 2 engine room relay block.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      BBC relay terminal 3 - Body ground Always 9.5 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. CHECK HARNESS AND CONNECTOR (BBC RELAY - EFI MAIN NO. 3 RELAY)


    1. Remove the BBC relay from No. 2 engine room relay block.

    2. Remove the EFI MAIN NO. 3 relay from No. 1 engine room relay block and junction block.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      BBC relay terminal 2 - EFI MAIN NO. 3 relay terminal 5 Always Below 1 Ω
      BBC relay terminal 2 or EFI MAIN NO. 3 relay terminal 5 - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. INSPECT EFI-MAIN NO. 3 RELAY


    1. Inspect the EFI-MAIN NO. 3 relay.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE EFI-MAIN NO. 3 RELAY

    OK

  10. CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 3 RELAY - BODY GROUND)


    1. Remove the EFI-MAIN NO. 3 relay from the No. 1 engine room relay block and junction block assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      EFI-MAIN NO. 3 relay terminal 1 - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  11. CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 3 RELAY)

    B006D7GC02
    *A for LHD *B for RHD
    *1 No. 1 Engine Room Relay Block and Junction Block Assembly *a EFI-MAIN NO. 3 Relay Terminal

    1. Remove the EFI-MAIN NO. 3 relay from the No. 1 engine room relay block and junction block assembly.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      EFI MAIN NO. 3 relay terminal 3 - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  12. CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 3 RELAY - EFI MAIN NO. 1 RELAY)


    1. Remove the EFI MAIN NO. 1 relay and EFI MAIN NO. 3 relay from No. 1 engine room relay block and junction block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      EFI MAIN NO. 3 relay terminal 2 - EFI MAIN NO. 1 relay terminal 5 Always Below 1 Ω
      EFI MAIN NO. 3 relay terminal 2 or EFI MAIN NO. 1 relay terminal 5 - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    GO TO ECM POWER SOURCE CIRCUIT Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  13. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - PASSENGER SIDE JUNCTION BLOCK ASSEMBLY)


    1. Disconnect the engine stop and start ECU connector.

    2. Disconnect the passenger side junction block assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G84-18 (IG2) - 4A-35 Always Below 1 Ω
      G84-18 (IG2) or 4A-35 - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    GO TO ENTRY AND START SYSTEM (FOR START FUNCTION) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR