BLACK OUT TAPE(for Rear Door) INSTALLATION

PROCEDURE


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. REPAIR INSTRUCTION

    Click here

  3. INSTALL NO. 2 BLACK OUT TAPE


    1. A005CFTE03
      Text in Illustration
      *A LH Side
      *B RH Side
      *a Perforation
      *b Triangle
      *c Straight Line
      *d Remove

      Remove the portion of the No. 2 black out tape at the perforation as shown in the illustration.

    2. Refer to the illustration to position the No. 2 black out tape.

      A005DZ8E01
      Standard Measurement
      Dimension Measurement
      A 2.0 to 4.0 mm (0.0787 to 0.157 in.)
      B 4.0 to 6.0 mm (0.157 to 0.236 in.)

    3. Remove the release paper and apply the tape.

  4. INSTALL REAR DOOR LOWER OUTSIDE STRIPE


    1. Refer to the illustration to position the rear door lower outside stripe.

      A005DC7E03
      Text in Illustration
      *A LH Side *B RH Side
      *a Triangle *b Edge of Curved Surface
      *c Straight Line - -
      Standard Measurement
      Dimension Measurement
      A 2.0 mm (0.0787 in.)

    2. Remove the release paper and apply the stripe.

  5. INSTALL REAR DOOR UPPER OUTSIDE STRIPE


    1. Refer to the illustration to position the rear door upper outside stripe.

      A005CZPE03
      Text in Illustration
      *A LH Side *B RH Side
      *a Triangle *b Edge of Curved Surface
      *c Straight Line - -
      Standard Measurement
      Dimension Measurement
      A 2.0 mm (0.0787 in.)

    2. Remove the release paper and apply the stripe.

  6. INSTALL REAR DOOR OUTSIDE STRIPE


    1. Refer to the illustration to position the rear door outside stripe.

      A005BBEE03
      Text in Illustration
      *A RH Side *B LH Side
      *a Triangle *b Edge of Curved Surface
      *c Straight Line - -
      Standard Measurement
      Dimension Measurement
      A 2.0 mm (0.0787 in.)

    2. Remove the release paper and apply the stripe.

  7. INSTALL REAR DOOR WEATHERSTRIP


    1. Engage the clip and install the rear door weatherstrip.

  8. INSTALL REAR DOOR FRAME GARNISH (w/o Rear Door Sunshade)

    Click here

  9. INSTALL REAR NO. 2 DOOR FRAME GARNISH (w/o Rear Door Sunshade)

    Click here

  10. INSTALL REAR DOOR FRAME GARNISH (w/ Rear Door Sunshade)

    Click here

  11. INSTALL REAR NO. 2 DOOR FRAME GARNISH (w/ Rear Door Sunshade)

    Click here

  12. INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING

    Click here

  13. INSTALL REAR DOOR BELT MOULDING ASSEMBLY

    Click here

  14. INSTALL REAR DOOR GLASS SUB-ASSEMBLY

    Click here

  15. INSTALL REAR DOOR REAR GUIDE SEAL

    Click here

  16. INSTALL REAR DOOR WINDOW GUIDE SUB-ASSEMBLY

    Click here

  17. INSTALL REAR DOOR GLASS RUN

    Click here

  18. INSTALL REAR DOOR SERVICE HOLE COVER

    Click here

  19. INSTALL REAR DOOR TRIM BRACKET

    Click here

  20. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

    Click here

  21. INSTALL REAR DOOR ARMREST COVER

    Click here

  22. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

    Click here

  23. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

    Click here

  24. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  25. INSTALL DECK FLOOR BOX RH

    Click here

  26. INSTALL REAR DECK FLOOR BOX

    Click here

  27. INSTALL NO. 1 DECK BOARD

    Click here

  28. INSTALL NO. 2 DECK BOARD

    Click here

  29. INSTALL DECK BOARD ASSEMBLY

    Click here

  30. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here

  31. INSPECT POWER WINDOW OPERATION

    Click here