POWER WINDOW CONTROL SYSTEM OPERATION CHECK

  1. CHECK WINDOW LOCK SWITCH

    Tip:

    Before performing the window lock switch operation check, make sure that the window lock switch is off (the switch is not pushed in).

    1. When the window lock switch of the multiplex network master switch assembly is pushed in. Check that the power window switch operation indicators for all of switches other than those on the multiplex network master switch are off and that the frontpassenger and rear windows are disabled.

      OK

      Front passenger and rear windows are disabled.

      Tip:

      Even when the window lock switch of the multiplex network master switch assembly is pushed in, remote manual up and down and auto up and down functions can be operated.

    2. When the window lock switch is pushed in again. Check that all ofthe power window switch operation indicators illuminate and that the front passenger and rearwindows can be operated normally.

      OK

      Front passenger and rear windows operate normally.

  2. CHECK MANUAL UP / DOWN FUNCTION

    1. Check that the driver side power window operates as follows:

      Table 1. OK

      Condition

      Master Switch

      Switch Operation

      Power Window

      Engine switch on (IG)

      Driver side

      Pulled halfway up

      UP (Closes)

      Pushed halfway down

      DOWN (Opens)

    2. Check that the front passenger side window and rear power windows operate as follows:

      Table 2. OK

      Condition

      Regulator Switch

      Switch Operation

      Power Window

      • Engine switch on (IG)

      • Window lock switch off

      Front passenger side

      Pulled halfway up

      UP (Closes)

      Pushed halfway down

      DOWN (Opens)

      Rear LH side

      Pulled halfway up

      UP (Closes)

      Pushed halfway down

      DOWN (Opens)

      Rear RH side

      Pulled halfway up

      UP (Closes)

      Pushed halfway down

      DOWN (Opens)

  3. CHECK AUTO UP / DOWN FUNCTION

    1. Check that the driver side power window operates as follows:

      Table 3. OK

      Condition

      Master Switch

      Switch Operation

      Power Window

      Engine switch on (IG)

      Driver side

      Pulled up (One touch operation)

      AUTO UP (Closes)

      Pushed down (One touch operation)

      AUTO DOWN (Opens)

    2. Check that the front passenger side window and rear power windows operate as follows:

      Table 4. OK

      Condition

      Regulator Switch

      Switch Operation

      Power Window

      • Engine switch on (IG)

      • Window lock switch off

      Front passenger side

      Pulled up (One touch operation)

      AUTO UP (Closes)

      Pushed down (One touch operation)

      AUTO DOWN (Opens)

      Rear LH side

      Pulled up (One touch operation)

      AUTO UP (Closes)

      Pushed down (One touch operation)

      AUTO DOWN (Opens)

      Rear RH side

      Pulled up (One touch operation)

      AUTO UP (Closes)

      Pushed down (One touch operation)

      AUTO DOWN (Opens)

  4. CHECK REMOTE MANUAL UP / DOWN FUNCTION

    1. Check that the front passenger side window and rear power windows operate as follows:

      Table 5. OK

      Condition

      Master Switch

      Switch Operation

      Power Window

      Engine switch on (IG)

      Front passenger side

      Pulled halfway up

      UP (Closes)

      Pushed halfway down

      DOWN (Opens)

      Rear LH side

      Pulled halfway up

      UP (Closes)

      Pushed halfway down

      DOWN (Opens)

      Rear RH side

      Pulled halfway up

      UP (Closes)

      Pushed halfway down

      DOWN (Opens)

  5. CHECK REMOTE AUTO UP / DOWN FUNCTION

    1. Check that the front passenger side window and rear power windows operate as follows:

      Table 6. OK

      Condition

      Master Switch

      Switch Operation

      Power Window

      Engine switch on (IG)

      Front passenger side

      Pulled up (One touch operation)

      AUTO UP (Closes)

      Pushed down (One touch operation)

      AUTO DOWN (Opens)

      Rear LH side

      Pulled up (One touch operation)

      AUTO UP (Closes)

      Pushed down (One touch operation)

      AUTO DOWN (Opens)

      Rear RH side

      Pulled up (One touch operation)

      AUTO UP (Closes)

      Pushed down (One touch operation)

      AUTO DOWN (Opens)

  6. CHECK POWER WINDOW OPERATION FUNCTION AFTER ENGINE SWITCH IS TURNED OFF

    1. Check that all the power windows can be operated with the multiplex network master switch and power window regulator switch (for front passenger side, rear LH and RH sides) after the engine switch is turned off.

      Tip:

      If the window lock switch is on, the windows cannot be operated using the power window regulator switch assemblies (for front passenger, rear LH and rear RH sides) and power window regulator master switch (remote function). Therefore, turn the window lock switch off before checking the window operation.

    2. Check that the key-off operation function does not operate after the driver side door or front passenger side door is opened.

      Tip:

      Even if the driver door or front passenger door is opened during automatic window operation while the key-off operation function is on, the window will continue operating.

    3. Check that all the power windows cannot be operated after more than approximately 43 seconds have elapsed since the engine switch was turned off.

  7. CHECK KEY-LINKED OPEN AND CLOSE FUNCTION

    Note:

    This inspection is possible only when the key-linked open and close function is set to ON through the customize function using the intelligent tester (the default setting is OFF).

    1. Check that all power windows operate as follows:

      Table 7. OK

      Condition

      Door Key Cylinder Operation

      Power Window

      No key is inside vehicle and all doors are closed

      Held in lock position for more than 2 seconds

      Up (Closes)

      No key is inside vehicle and all doors are closed

      Returned to neutral position

      Stop

      No key is inside vehicle and all doors are closed

      Held in unlock position for more than 2 seconds

      Down (Opens)

      No key is inside vehicle and all doors are closed

      Returned to neutral position

      Stop

  8. CHECK WIRELESS TRANSMITTER-LINKED OPEN AND CLOSE FUNCTION

    Note:

    This inspection is possible only when the wireless transmitter-linked open function is set to ON through the customize function using the intelligent tester (the default setting is OFF).

    1. Check that all power windows operate as follows when operating the transmitter:

      Table 8. OK

      Condition

      Transmitter Operation

      Power Window

      No key is inside vehicle

      UNLOCK switch pressed for more than 3.0 seconds

      Down (Opens)

      No key is inside vehicle

      UNLOCK switch released

      Stops

      No key is inside vehicle, and all doors are closed and locked

      LOCK switch pressed for more than 3.0 seconds

      Up (Closes)

      No key is inside vehicle, and all doors are closed and locked

      LOCK switch released

      Stops

  9. CHECK JAM PROTECTION FUNCTION

    1. Check the basic function.

      CAUTION:

      Do not put your fingers between the door frame and door glass to check the jam protection function. Also, prevent any part of your body from being caught during inspection.

      Tip:

      The jam protection function is operative during both the auto up and manual up operations while the engine is running or the engine switch is on (IG), and also 43 sec. have elapsed after the engine switch is turned off.

      1. Fully open the window.

      2. B316219C01

        *1

        Thick Book

        *2

        Cloth

        Set a thick book wrapped with a piece of cloth near the window fully closed position.

      3. Operate the auto up or manual up function to check that the power window goes down after the book is caught between the window and door frame, and stops when the opening reaches approximately 200 mm (7.87 in.).

        Tip:

        The power window moves down approximately 125 mm (4.93 in.). However, when the opening does not reach 200 mm (7.87 in.), the power window continues to go down until the opening reaches 200 mm (7.87 in.) or until approximately 5 seconds elapse.

      4. While the power window is moving down, check that the door glass cannot be raised when the power window switch is used.

  10. CHECK POWER WINDOW SWITCH LED ILLUMINATION

    1. Check the LED illumination (multiplex network master switch).

      1. Check that the LEDs located on the multiplex network master switch illuminate when the engine switch is turned on (IG).

    2. Check the LED illumination (power window regulator switch [for front passenger side]).

      1. Check that the LED located on the power window regulator switch (for front passenger side) illuminates when the engine switch is turned on (IG).

        Tip:

        If the window lock switch is on, the LED located on the power window regulator switch (for front passenger side) does not illuminate. Therefore, turn the window lock switch off before checking the LED illumination.

    3. Check the LED illumination (power window regulator switch [for rear LH and rear RH]).

      1. Check that the LED located on each power window regulator switch (for rear LH and rear RH) illuminates when the engine switch is turned on (IG).

        Tip:

        If the window lock switch is on, the LEDs located on the power window regulator switch assemblies (for rear LH and rear RH) do not illuminate. Therefore, turn the window lock switch off before checking the LED illumination.