LOWER INSTRUMENT PANEL REMOVAL

PROCEDURE


  1. PRECAUTION

    Click here

  2. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY

    Click here

  3. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  5. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A005DI3

      Disengage the 3 claws and guide.

    2. Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.

  6. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    1. Open the glove compartment door.

    2. A005EGZE03
      Text in Illustration
      *1 Glove Compartment Door Stopper Sub-assembly
      *2 Stopper

      Disengage the claw and release the glove compartment door stopper sub-assembly.

    3. Slightly bend stoppers (A) and (B) in the directions indicated by the arrows in the illustration and pull the glove compartment door assembly until the stoppers are released.

    4. A005AJ9E03
      Text in Illustration
      *a Closed
      *b Opened Approximately 65°

      Open the glove compartment door assembly to approximately 65° from its closed position. Pull it horizontally in the direction indicated by the arrow to disengage the 2 hinges and remove the glove compartment door assembly.

      Note

      Pulling the glove compartment door assembly upward to remove it causes the hinges to deform. Be sure to pull out the glove compartment door assembly horizontally.

  7. REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY


    1. A005A2S

      Disengage the claw to remove the glove compartment door stopper sub-assembly.

  8. REMOVE CENTER FLOOR CARPET COVER RH


    1. A005E82E03

      Pull the front center floor carpet cover RH in the direction indicated by the arrow to disengage the 4 claws and guide, and remove the center floor carpet cover RH.

  9. REMOVE CENTER FLOOR CARPET COVER LH


    1. A0059N4E03

      Pull the front center floor carpet cover LH in the direction indicated by the arrow to disengage the 4 claws and guide, and remove the center floor carpet cover LH.

  10. REMOVE UPPER CONSOLE PANEL

    Click here

  11. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

    Click here

  12. REMOVE FRONT NO. 2 CONSOLE BOX INSERT

    Click here

  13. REMOVE CONSOLE BOX ASSEMBLY

    Click here

  14. REMOVE COMBINATION METER ASSEMBLY


    1. A0059U2

      Remove the 4 screws <E>.

    2. Disengage the clamp.

    3. Disconnect each connector to remove the combination meter assembly.

  15. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio Receiver Type)

    Click here

  16. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (for Navigation Receiver Type)

    Click here

  17. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A005EHH

      Using a moulding remover, disengage the 11 claws.

    2. Disengage the clamp.

    3. Disconnect each connector to remove the lower instrument panel finish panel sub-assembly.

  18. REMOVE AIR CONDITIONING CONTROL ASSEMBLY

    Click here

  19. REMOVE SHIFT LOCK CONTROL UNIT ASSEMBLY

    Click here

  20. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  21. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

    Click here

  22. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A005BQ1

      Remove the 2 screws <E>.

    2. Disengage the 2 claws and guide.

    3. Disconnect each connector.

    4. Disengage the clamp to remove the No. 1 instrument panel under cover sub-assembly.

  23. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  24. REMOVE GLOVE BOX LIGHT ASSEMBLY

    Click here

  25. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A005CON

      Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

  26. REMOVE ANTENNA CORD SUB-ASSEMBLY (for LHD)

    Click here

  27. REMOVE ANTENNA CORD SUB-ASSEMBLY (for RHD)

    Click here

  28. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for LHD)


    1. A005E5J

      Disconnect the connector.

    2. A005EBB

      Disengage the claw and disconnect the connector as shown in the illustration.

    3. Disengage each clamp.

      A005B5OE02
      Text in Illustration
      *1 Room Temperature Sensor - -

    4. Disengage the 2 claws to disconnect the room temperature sensor from the lower instrument panel sub-assembly.

    5. Disengage the 2 claws.

    6. Remove the 2 bolts <A>, 10 screws <C> and screw <D> and lower instrument panel sub-assembly.

      A005BY3E03
      Text in Illustration
      *1 Bolt <A> *2 Screw <C>
      *3 Screw <D> - -

  29. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)


    1. Disengage the 2 claws to disconnect the DLC3.

      A005DFNE02
      Text in Illustration
      *1 DLC3 *2 Room Temperature Sensor

    2. Disengage each clamp.

    3. Disengage the 2 claws to disconnect the room temperature sensor from the lower instrument panel sub-assembly.

    4. Remove the 2 bolts <A>, 10 screws <C> and screw <D> and lower instrument panel sub-assembly.

      A0059UAE02
      Text in Illustration
      *1 Bolt <A> *2 Screw <C>
      *3 Screw <D> - -