CAN COMMUNICATION SYSTEM Check Bus 4 Line for Short to +B

DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when there is no resistance between terminal 22 (CA2H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 7 (CA2L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.

Symptom Trouble Area
There is no resistance between terminal 22 (CA2H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 7 (CA2L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.

  • Short to +B in CAN main bus wire

  • Short to +B in CAN branch wire

  • Central gateway ECU (network gateway ECU)

  • Steering sensor

  • Rack and pinion power steering gear assembly

  • Airbag ECU assembly

  • Yaw rate sensor

  • Brake actuator assembly (Skid control ECU)

  • Pedestrian detection ECU assembly

  • Rear steering control ECU*1

  • Parking brake ECU assembly

  • Absorber control ECU*2

  • Suspension control ECU*3

  • Tire pressure warning ECU and receiver

  • Front steering control ECU*4

  • No. 1 CAN junction terminal

  • No. 2 CAN junction terminal

  • No. 4 CAN junction connector

  • No. 12 CAN junction connector

  • No. 14 CAN junction connector
*1: w/ Dynamic Rear Steering System
*2: w/ Adaptive Variable Suspension System
*3: w/ Air Suspension System
*4: w/ Variable Gear Ratio Steering System

WIRING DIAGRAM

B006AMNE01
B006DAPE01

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

Note


  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • Some parts must be initialized and set when replacing or removing and installing parts.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

    DTC check procedure: Turn the engine switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here

Tech Tips


  • Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

  • When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE


  1. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the G122 No. 4 CAN junction connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition Connected to
      G122-12 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 12 CAN junction connector
      G122-1 (CANL) - G20-16 (BAT)
      G122-13 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
      G122-2 (CANL) - G20-16 (BAT)
      G122-14 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Steering sensor
      G122-3 (CANL) - G20-16 (BAT)
      G122-15 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 14 CAN junction connector
      G122-4 (CANL) - G20-16 (BAT)
      G122-16 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Airbag ECU assembly
      G122-5 (CANL) - G20-16 (BAT)
      G122-17 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Yaw rate sensor
      G122-6 (CANL) - G20-16 (BAT)
      G122-18 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Pedestrian detection ECU assembly
      G122-7 (CANL) - G20-16 (BAT)
      G122-19 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Front steering control ECU*
      G122-8 (CANL) - G20-16 (BAT)
      *: w/ Variable Gear Ratio Steering System
      Result
      Result Proceed to
      OK A
      NG (Central gateway ECU [network gateway ECU] CAN branch wire) B
      NG (No. 12 CAN junction connector CAN main wire) C
      NG (No. 14 CAN junction connector CAN main wire) D
      NG (Wire to ECU or sensor) E

    A

    REPLACE NO. 4 CAN JUNCTION CONNECTOR

    C

    CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 12 CAN JUNCTION CONNECTOR) Click here

    D

    CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 14 CAN JUNCTION CONNECTOR) Click here

    E

    GO TO STEP 5 Click here

    B

  2. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 4 CAN JUNCTION CONNECTOR)


    1. Reconnect the G122 No. 4 CAN junction connector.

    2. Disconnect the G66 central gateway ECU (network gateway ECU) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G66-22 (CA2H) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G66-7 (CA2L) - G20-16 (BAT)
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 4 CAN JUNCTION CONNECTOR)

  3. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 12 CAN JUNCTION CONNECTOR)


    1. Reconnect the G122 No. 4 CAN junction connector.

    2. Disconnect the L117 No. 12 CAN junction connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition Connected to
      L117-1 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Brake actuator assembly (skid control ECU)
      L117-7 (CANL) - G20-16 (BAT)
      L117-2 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 4 CAN junction connector
      L117-8 (CANL) - G20-16 (BAT)
      L117-3 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 2 CAN junction terminal
      L117-9 (CANL) - G20-16 (BAT)
      L117-5 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Rack and pinion power steering gear assembly
      L117-11 (CANL) - G20-16 (BAT)
      for RHD
      Tester Connection Condition Specified Condition Connected to
      L117-1 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 4 CAN junction connector
      L117-7 (CANL) - G20-16 (BAT)
      L117-2 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 2 CAN junction terminal
      L117-8 (CANL) - G20-16 (BAT)
      L117-4 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Rack and pinion power steering gear assembly
      L117-10 (CANL) - G20-16 (BAT)
      L117-6 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Brake actuator assembly (skid control ECU)
      L117-12 (CANL) - G20-16 (BAT)
      Result
      Result Proceed to
      OK A
      NG (No. 4 CAN junction connector CAN main wire) B
      NG (Wire to ECU or sensor) C

    A

    REPLACE NO. 12 CAN JUNCTION CONNECTOR

    B

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 12 CAN JUNCTION CONNECTOR - NO. 4 CAN JUNCTION CONNECTOR)

    C

    GO TO STEP 5 Click here

  4. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 14 CAN JUNCTION CONNECTOR)


    1. Reconnect the G122 No. 4 CAN junction connector.

    2. Disconnect the L119 No. 14 CAN junction connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition Connected to
      L119-1 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 1 CAN junction terminal
      L119-11 (CANL) - G20-16 (BAT)
      L119-2 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 4 CAN junction connector
      L119-12 (CANL) - G20-16 (BAT)
      L119-3 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Parking brake ECU assembly
      L119-13 (CANL) - G20-16 (BAT)
      L119-4 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Absorber control ECU*1
      L119-14 (CANL) - G20-16 (BAT)
      L119-5 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Tire pressure warning ECU and receiver
      L119-15 (CANL) - G20-16 (BAT)
      L119-7 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Suspension control ECU*2
      L119-17 (CANL) - G20-16 (BAT)
      L119-8 (CANH) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Rear steering control ECU*3
      L119-18 (CANH) - G20-16 (BAT)
      *1: w/ Adaptive Variable Suspension System
      *2: w/ Air Suspension System
      *3: w/ Dynamic Rear Steering System
      Result
      Result Proceed to
      OK A
      NG (No. 4 CAN junction connector CAN main wire) B
      NG (Wire to ECU or sensor) C

    A

    REPLACE NO. 14 CAN JUNCTION CONNECTOR

    B

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 14 CAN JUNCTION CONNECTOR - NO. 4 CAN JUNCTION CONNECTOR)

    C

  5. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)


    1. Reconnect all wire harness connectors.

    2. Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus wire shorted to +B is connected.

      Click here

    3. B006B12C51
      *a

      Component with harness connected

      (Central Gateway ECU [Network Gateway ECU])

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G66-22 (CA2H) - G20-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G66-7 (CA2L) - G20-16 (BAT)

      Tech Tips


      • If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

      • If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECU OR SENSOR

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR