ECD SYSTEM, Diagnostic DTC:P2195

DTC Code DTC Name
P2195 O2 Sensor Signal Biased / Stuck Lean Bank 1 Sensor 1

DESCRIPTION

Refer to DTC P0030.

Click here

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

P2195

O2 Sensor Signal Biased / Stuck Lean Bank 1 Sensor 1

Oxygen concentration higher than estimated concentration for specified condition.

(3 trip detection logic)

  • Open or short in air fuel ratio sensor (for sensor 1) circuit

  • Air fuel ratio sensor (for sensor 1)

  • Exhaust system exhaust gas leak

  • ECM

Does not come on

DTC stored
Table 1. Related Data List

DTC No.

Data List

P2195

  • O2 Sensor Lambda Bank 1 Sensor 1

  • O2 Sensor Lambda Bank 1 Sensor 2

WIRING DIAGRAM

Refer to DTC P0030.

Click here

CAUTION / NOTICE / HINT

Note:

  • When replacing the ECM and/or air fuel ratio sensor, the ECM needs registration and initialization.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tip:

  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

  1. Air fuel ratio sensors functional check

    Refer to DTC P013A.

    Click here

PROCEDURE

  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2195)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

      Powertrain > Engine and ECT > Trouble Codes

    4. Read the DTCs.

      Result

      Result

      Proceed to

      DTC P2195

      A

      DTC P2195 and other DTCs

      B
      Tip:

      • If any DTCs other than P2195 are output, troubleshoot those DTCs first.

      • If a DTC is stored for the heater system of the air fuel ratio sensor, first repair the heater system.

    B

    GO TO DTC CHART

    Click hereClick hereClick here

    A

  2. CHECK EXHAUST SYSTEM

    1. Check for exhaust gas leak from the exhaust system.

      OK

      No exhaust gas leak.

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE EXHAUST SYSTEMClick here

    OK

  3. CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 1) - ECM)

    1. Disconnect the air fuel ratio sensor (for sensor 1) connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      B213-1 (AF1+) - B220-127 (AF1+)

      Always

      Below 1 Ω

      B213-2 (AF1-) - B220-126 (AF1-)

      Always

      Below 1 Ω

      B213-3 (HAF1) - B220-46 (HAF1)

      Always

      Below 1 Ω

      B213-5 (TR1) - B220-128 (TR1)

      Always

      Below 1 Ω

      B213-6 (RE1) - B220-125 (RE1)

      Always

      Below 1 Ω

      B213-1 (AF1+) or B220-127 (AF1+) - Body ground

      Always

      10 kΩ or higher

      B213-2 (AF1-) or B220-126 (AF1-) - Body ground

      Always

      10 kΩ or higher

      B213-3 (HAF1) or B220-46 (HAF1) - Body ground

      Always

      10 kΩ or higher

      B213-5 (TR1) or B220-128 (TR1) - Body ground

      Always

      10 kΩ or higher

      B213-6 (RE1) or B220-125 (RE1) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTORClick here

    OK

  4. REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 1)

    1. Replace the air fuel ratio sensor (for sensor 1).

      Click here

    2. Perform the O2 sensor learning value reset.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  5. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

      Powertrain > Engine and ECT > Trouble Codes

    8. Read the DTCs.

      Result

      Result

      Proceed to

      No DTC output

      A

      DTC P2195

      B
    A

    END

    B

  6. REPLACE ECM

    1. Replace the ECM.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  7. REPAIR OR REPLACE HARNESS OR CONNECTOR

    1. Repair or replace the harness or connector.

    Result

    Proceed to

    NEXT
    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  8. REPAIR OR REPLACE EXHAUST SYSTEM

    1. Repair or replace the exhaust system.

    Result

    Proceed to

    NEXT
    NEXT

  9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the GTS to the DLC3

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

      Powertrain > Engine and ECT > Trouble Codes

    8. Confirm that the DTC is not output again.

    Result

    Proceed to

    NEXT
    NEXT

    END