METER / GAUGE SYSTEM OPERATION CHECK

CHECK INDICATOR/WARNING LIGHT

1. Check the following indicators and warning lights.

   Indicator/Warning Light	Switch Condition	Specified Condition
   ABS warning light	Ignition switch off → ON	Comes on for 3 seconds
   SLIP indicator light
   Eco driving indicator light*1
   BRAKE warning light
   LEVELING indicator light*2
   VSC OFF indicator light
   Tire pressure warning light*3
   Stop and start cancel indicator light*4
   Stop and start indicator light*4
   Automatic high beam indicator light*5
   PCS indicator light*6
   SRS warning light	Ignition switch off → ON	Comes on for 6 seconds
   CHARGE warning light	Ignition switch off → ON	Illuminates when ignition switch turned to ON Turns off when engine started
   EPS warning light
   MIL

   • *1: for CVT

   • *2: w/ HID Headlight System

   • *3: w/ Tire Pressure Warning System

   • *4: w/ Stop and Start System

   • *5: w/ Automatic High Beam System

   • *6: w/ Pre-collision System

CHECK SPEEDOMETER

1. Using a speedometer tester, check that the speedometer reading is within the allowable range shown in the table below. Also, check for proper operation of the odometer.

   Reference

   Table 1. for mph

   Standard Indication	Acceptable Range
   20 mph	21 to 23.5 mph
   40 mph	42 to 44.5 mph
   60 mph	62.5 to 66 mph
   80 mph	83.1 to 87.1 mph
   100 mph	103.9 to 108.4 mph
   120 mph	124.7 to 129.6 mph
   140 mph	145.4 to 150.7 mph

   Table 2. for km/h

   Standard Indication	Acceptable Range
   20 km/h	21 to 25 km/h
   40 km/h	41.7 to 46.2 km/h
   60 km/h	62.7 to 67.2 km/h
   80 km/h	83.4 to 88.4 km/h
   100 km/h	104.3 to 109.3 km/h
   120 km/h	125.1 to 130.6 km/h
   140 km/h	145.8 to 151.8 km/h
   160 km/h	166.2 to 173.2 km/h
   180 km/h	186.9 to 194.5 km/h
   200 km/h	207.7 to 215.7 km/h
   220 km/h	228.4 to 236.8 km/h
   240 km/h	229.2 to 258 km/h

   If the result is not as specified, the speedometer may have a malfunction.

   Note:

   Do not use worn, underinflated or overinflated tires, as the speedometer reading will be inaccurate.

2. Check the deflection width of the speedometer indicator.

   Reference

   Within 0.3°

CHECK TACHOMETER

1. Connect a tune-up tachometer and start the engine.

2. Compare the test results with the tachometer indicator.

   DC 13.5 V, at 25°C (77°F)

   Standard Indication	Acceptable Range Data in ( ) is for reference
   700 rpm	630 to 770 rpm
   1000 rpm	(900 to 1100 rpm)
   2000 rpm	(1850 to 2150 rpm)
   3000 rpm	2800 to 3200 rpm
   4000 rpm	(3800 to 4200 rpm)
   5000 rpm	4800 to 5200 rpm
   6000 rpm	(5750 to 6250 rpm)
   7000 rpm	6700 to 7300 rpm
   8000 rpm	7700 to 8300 rpm

   If the result is not as specified, the tachometer may have a malfunction.

CHECK METER/GAUGE

1. Connect the intelligent tester to the DLC3.

2. Perform the Active Test (Click here).

   OK

   Each meter/gauge needle indication is normal.

CHECK WARNING/INDICATOR LIGHT

1. Connect the intelligent tester to the DLC3.

2. Perform the Active Test (Click here).

   OK

   Each warning/indicator light can be turned on and off using the intelligent tester.

INSPECT MULTI-INFORMATION DISPLAY

1. 

   Connect the intelligent tester to the DLC3.

2. Perform the Active Test (Click here).

   Tip:

   If this Active Test is being performed and the ignition switch is turned off and then to ON, the clock and ODO/TRIP display background may turn white. If this occurs, end the Active Test and turn the ignition switch off.

   OK

   All dots in the multi-information display can be turned on and off using the intelligent tester.