LIGHTING SYSTEM DATA LIST / ACTIVE TEST

  1. DATA LIST

    Note:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    Tip:

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    1. Connect the GTS to the DLC3.

    2. Turn the power switch to on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List / All Data.

    5. According to the display on the GTS, read the Data List.

      Body Electrical > Main Body > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      ACC SW

      Power switch on (ACC) signal

      ON or OFF

      ON: Power switch on (ACC)

      OFF: Power switch off

      "ON" is also displayed for this item when the power switch is on (IG).

      IG SW

      Power switch on (IG) signal

      ON or OFF

      ON: Power switch on (IG)

      OFF: Power switch off

      "OFF" is also displayed for this item when the power switch is on (ACC).

      RR Door Courtesy SW

      Rear door courtesy light switch RH signal

      ON or OFF

      ON: Rear door RH open

      OFF: Rear door RH closed

      -

      RL Door Courtesy SW

      Rear door courtesy light switch LH signal

      ON or OFF

      ON: Rear door LH open

      OFF: Rear door LH closed

      -

      Back Door Courtesy SW

      Back door courtesy light switch signal

      ON or OFF

      ON: Back door open

      OFF: Back door closed

      -

      FR Door Lock Pos

      Front door unlock detection switch RH signal

      UNLOCK or LOCK

      UNLOCK: Front door RH unlocked

      LOCK: Front door RH locked

      -

      FR Door Courtesy SW

      Front door courtesy light switch RH signal

      ON or OFF

      ON: Front door RH open

      OFF: Front door RH closed

      -

      FL Door Lock Pos

      Front door unlock detection switch LH signal

      UNLOCK or LOCK

      UNLOCK: Front door LH unlocked

      LOCK: Front door LH locked

      -

      FL Door Courtesy SW

      Front door courtesy light switch LH signal

      ON or OFF

      ON: Front door LH open

      OFF: Front door LH closed

      -

      RR-Door Lock Pos SW

      LH and RH side rear door unlock detection switch signal

      ON or OFF

      ON: LH or RH side rear door unlocked

      OFF: LH and RH side rear door locked

      -

      RL-Door Lock Pos SW

      LH and RH side rear door unlock detection switch signal

      ON or OFF

      ON: LH or RH side rear door unlocked

      OFF: LH and RH side rear door locked

      -

      Interior Light Control

      Function which controls interior lights

      ON or OFF

      Customized setting displayed

      -

      I/L ON W/Door Key Unlock

      Function which turns on interior lights when door is unlocked

      ON or OFF

      Customized setting displayed

      -

      Lighting Time

      Lighting time after closing all doors

      7.5 s, 15 s or 30 s

      Customized setting displayed

      -

      Room Light when Aprchd

      Function which turns on room lights when key is brought within vehicle exterior detection area

      ON or OFF

      Customized setting displayed

      -

      I/L when ACC OFF

      Function which turns on lights when power switch is turned from on (IG) or on (ACC) to off

      ON or OFF

      Customized setting displayed

      -

  2. ACTIVE TEST

    Tip:

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the GTS to the DLC3.

    2. Turn the power switch to on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / (desired system) / Active Test.

    5. According to the display on the GTS, perform the Active Test.

      Body Electrical > Main Body > Active Test

      Tester Display

      Measurement Item

      Control Range

      Diagnostic Note

      Illuminated Entry System

      Map light and No. 1 room light

      ON or OFF

      Turn the map light switch and No. 1 room light switch to the DOOR position.

      Relay for Interior Light Auto Cut Function

      DOME CUT relay

      ON or OFF

      -

      Body Electrical > Entry&Start > Active Test

      Tester Display

      Measurement Item

      Control Range

      Diagnostic Note

      Power/Engine SW Light

      Power switch Illumination

      ON or OFF

      -